Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: powerslinky on 07 June 2015, 17:17:50
-
Hi all
I have removed all 4 cams from the breaker . All 4 have a "G" prefix letter ( GC26 as one example)
Is it correct for a 3.2 to have "G" prefix cams on all 4 camshafts.
Somewhere in my head was the formula of inlet should be "G" & exhaust "A" . . . or is that just the 3.0 engine. :-\
Just trying to confirm as I have listed these for sale in the parts section :-\ TIA
-
2 x G and 2 x J I believe. :-\
-
2 x G and 2 x J I believe. :-\
This :y
-
2 x G and 2 x J I believe. :-\
Umm ! these 4 all seem marked with a G as the first of 2 letters then 2 digits . Markings seem stamped into the shaft &
as said GC26 is one example . I have oiled them with clean 10- 40 & wrapped them in clingfilm marking each with where it
came from ( 1-3-5 inlet etc)
May have to unwrap them all & double check . . but I am sure they all prefix with G
Can anyone else confirm what & how they they should be marked in a late 3.2 ? :-\ :-\
-
2 x G and 2 x J I believe. :-\
Umm ! these 4 all seem marked with a G as the first of 2 letters then 2 digits . Markings seem stamped into the shaft &
as said GC26 is one example . I have oiled them with clean 10- 40 & wrapped them in clingfilm marking each with where it
came from ( 1-3-5 inlet etc)
May have to unwrap them all & double check . . but I am sure they all prefix with G
Can anyone else confirm what & how they they should be marked in a late 3.2 ? :-\ :-\
Right sorted . . . although all have an easily viewable GC prefix thats not the cam ID :-[ :-[ :-[
Inlets are marked with a very fine & quite difficult to see, G & a single digit & exhausts with a J & a single digit :y :y
Thanks Andy & James :y
-
The GC26 will probably be the cast number for the blank of the cam before it got profiled...
The G should be engraved onto a part of the camshaft that is near the front of the cam....
-
The GC26 will probably be the cast number for the blank of the cam before it got profiled...
The G should be engraved onto a part of the camshaft that is near the front of the cam....
Yep found it . . .hard to see for 58 year old with dodgy eyes ;D ;D ;D ;D thanks anyway :y
-
No problem fella, my eyes aint all that good these days either LOL
-
Hi all
I have removed all 4 cams from the breaker . All 4 have a "G" prefix letter ( GC26 as one example)
Is it correct for a 3.2 to have "G" prefix cams on all 4 camshafts.
Somewhere in my head was the formula of inlet should be "G" & exhaust "A" . . . or is that just the 3.0 engine. :-\
Just trying to confirm as I have listed these for sale in the parts section :-\ TIA
Forget the G prefix with numbers, its the other Bigger G (only on 2 of them) that you need to find on the other end of the Cam from memory. ;)
-
Hi all
I have removed all 4 cams from the breaker . All 4 have a "G" prefix letter ( GC26 as one example)
Is it correct for a 3.2 to have "G" prefix cams on all 4 camshafts.
Somewhere in my head was the formula of inlet should be "G" & exhaust "A" . . . or is that just the 3.0 engine. :-\
Just trying to confirm as I have listed these for sale in the parts section :-\ TIA
Forget the G prefix with numbers, its the other Bigger G (only on 2 of them) that you need to find on the other end of the Cam from memory. ;)
Yep . . found them now Chris . . Inlets are G Exhausts are J :y