Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1]   Go Down

Author Topic: Torque settings inlet manifold 2.6  (Read 1029 times)

0 Members and 1 Guest are viewing this topic.

grifter

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Paisley, Scotland
  • Posts: 902
  • Omega Baron
    • Omega 2.6 CD / Elite 3.2
    • View Profile
Torque settings inlet manifold 2.6
« on: 22 May 2017, 18:23:08 »
Hi, I checked the change gasket/clean plenum guide thinking one of them would have values for this, from the settings given I couldn't see anything about torque settings for the inlet manifold bridge, unless reading it wrong, I wouldn't imagine it was 8nm, but again I don't really know. The 6 torx bolts is the value I'm looking for.

http://www.omegaowners.com/forum/index.php?topic=90653.0

Below is what I could find. It's not 8nm is it? :)
:

Torque Values
EGR pipe to EGR valve 25Nm
Item   Value
Plenum to inlet   8Nm
Support bracket to EGR valve 20Nm
Cable tray to plenum   6Nm
Throttle body to plenum   8Nm
Breather bridge to plenum   8Nm


Cheers

G
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28197
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Torque settings inlet manifold 2.6
« Reply #1 on: 22 May 2017, 18:56:37 »
Where did those numbers come from ???
Logged
Onanists always think outside the box.

grifter

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Paisley, Scotland
  • Posts: 902
  • Omega Baron
    • Omega 2.6 CD / Elite 3.2
    • View Profile
Re: Torque settings inlet manifold 2.6
« Reply #2 on: 22 May 2017, 19:37:25 »
Quote from: Doctor Gollum on 22 May 2017, 18:56:37
Where did those numbers come from ???

Link in first post
Logged

YZ250

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Oxford/Bucks border
  • Posts: 4174
    • Black 3.2 Elite Estate
    • View Profile
Re: Torque settings inlet manifold 2.6
« Reply #3 on: 22 May 2017, 19:43:34 »
« Last Edit: 22 May 2017, 19:45:14 by YZ250 »
Logged
My fun car is a 2020 Bmw F32 430d M Sport with indicators.
My cruiser is an Audi A6 Avant S Line Black Edition with indicators.

Doctor Gollum

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28197
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Torque settings inlet manifold 2.6
« Reply #4 on: 22 May 2017, 20:11:10 »
Logged
Onanists always think outside the box.

grifter

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Paisley, Scotland
  • Posts: 902
  • Omega Baron
    • Omega 2.6 CD / Elite 3.2
    • View Profile
Re: Torque settings inlet manifold 2.6
« Reply #5 on: 22 May 2017, 20:17:48 »
Quote from: YZ250 on 22 May 2017, 19:43:34
Is it not in this lot?  :)

http://www.omegaowners.com/forum/index.php?topic=90519.0

Now that is what I'm torquing about!

Intake bridge to intake flange - 20nm
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.021 seconds with 21 queries.