Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: 1 2 [All]   Go Down

Author Topic: Where to Locate Axle Stands (Rear)  (Read 3894 times)

0 Members and 1 Guest are viewing this topic.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Where to Locate Axle Stands (Rear)
« on: 03 March 2019, 13:44:41 »

Planning to start changing rear wheel bearing, right side first. For safety would like to use stands, old wheels etc. Any recommendation for good places for those axle stands?
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28089
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #1 on: 03 March 2019, 14:10:56 »

Triangular plate on the subframe mount, with care you can jack it and place the stand on the same plate, but takes a bit of practice and experimenting to make it work.

From memory the axle stand locates on the side which is bolted deeper than the other two corners. This will make sense when you look at it :y
Logged
Onanists always think outside the box.

Nick W

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chatham, Kent
  • Posts: 10836
  • Rover Metro 1.8VVC
    • 3.0l Elite estate
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #2 on: 03 March 2019, 14:24:41 »

When I've done rear wheel bearings, I put the axle stands exactly where Al suggested.


Just out of interest, why are you doing both bearings? They're the sort of part and job that is best done only when necessary.
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #3 on: 03 March 2019, 14:27:37 »

Thanks DG and Nick W for tips. Right side is noisy and I remember someone here recommended to change them both.
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28089
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #4 on: 03 March 2019, 14:28:48 »

Thanks DG and Nick W for tips. Right side is noisy and I remember a complete psychopath recommended to change them both.
Fixed :o
Logged
Onanists always think outside the box.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #5 on: 06 May 2019, 18:46:36 »

I almost started this but I did not understand the recommended location where to put thestand. Triangle found but it looks thin and weak. In center of it there is a bolt and below that there is a rubber. Would it be bad idea to put it in the center?
Logged

Nick W

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chatham, Kent
  • Posts: 10836
  • Rover Metro 1.8VVC
    • 3.0l Elite estate
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #6 on: 06 May 2019, 19:27:32 »

Put the jack under the pivot of the suspension arm, and the stand under the triangle. That's all you need; don't over think it.
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #7 on: 07 May 2019, 15:39:08 »

OK, ok, thanks. I do my best.
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #8 on: 07 May 2019, 19:23:23 »

Still two things,
1. Does anybody remember the size of the hub nut
2. Is the right side nut with normal right hand thread, I can borrow a big impact tool up to 2000Nm, just want to confirm that I do not break anything...
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28089
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #9 on: 07 May 2019, 21:17:05 »

36mm and 270NM iirc :o
Logged
Onanists always think outside the box.

Enceladus

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • London
  • Posts: 1057
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #10 on: 07 May 2019, 22:24:09 »

36mm and 270NM iirc :o
300Nm methinks? Not that it makes it any easier.
Logged

Nick W

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chatham, Kent
  • Posts: 10836
  • Rover Metro 1.8VVC
    • 3.0l Elite estate
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #11 on: 07 May 2019, 23:16:07 »

36mm nut. They're both RH threads.
You probably won't get a 2000nm gun in the space!


Every knackered bearing I've replaced has been easy to undo; tightening them can be interesting.


How are you intending to extract the hub from the bearing?
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #12 on: 08 May 2019, 04:17:19 »

Morning

Thanks for all about dimension info and encouraging me (Nick W) that the nut is easy to remove...

1. Concerning the torque my friend has something like the enclosed Chicago one, not exactly this but similar; 1620 ft-lbs is higher than 2000 Nm if 1 ft-lb is 1.36 Nm and if I understood right (usually not).

https://www.ebay.com/itm/Chicago-Pneumatic-1-Drive-Impact-Wrench-with-6-Anvil-CP7778-6/132106872144?epid=1723724924&hash=item1ec22ee550:g:ktgAAOSw4C5cm6KP

2. Extracting the hub from the bearing the idea was to use method presented in Jan Suhr's nice guide, are there any alternative methods without special tools?
http://www.omegaowners.com/forum/index.php?topic=130619.0

3. Tightenig to 300 Nm is about 30kg by using 1 meter torsion bar, my weight is about 75 kg so with 1/2m something bolted to hub was my idea, any suggestions here?
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28089
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #13 on: 08 May 2019, 08:42:28 »

3. I used a torque wrench ::)

Actual setting is 320 NM :y

My torque wrench only goes to 300, so did it up with that plus a BFT smidge with a bar :y
Logged
Onanists always think outside the box.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #14 on: 08 May 2019, 19:19:32 »

OK, 320Nm when it is time for that. But I am going ahead: Shock lower mount, brakepads and drive shaft is away. As the shoes do not touch the drum when rotating the disc I can hear quite metallic sound so perhaps the diagnosis of bearing failure is correct and I continue tomorrow. I have 260 000 km behind and believe that it is time to change the bearing. Should it last longer?
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28089
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #15 on: 08 May 2019, 20:00:20 »

3. I used a torque wrench ::)

Actual setting is 320 NM :y

My torque wrench only goes to 300, so did it up with that plus a BFT smidge with a bar :y
I will correct that after work... That torque is for the front :-[
Logged
Onanists always think outside the box.

Enceladus

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • London
  • Posts: 1057
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #16 on: 08 May 2019, 23:01:49 »

OK, 320Nm when it is time for that.
Rear hub bearings are 300Nm.
It's the front hub bearings that are 320Nm.
Not that it makes much difference, but it does help to have the target understood and correct.
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #17 on: 09 May 2019, 04:05:11 »

OK, thanks correction, no problem yet, have to remove it first. Is there any typical life time for rear bearing of Omega?
Logged

mandula

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 174
    • Opel Omega -03, Z22XE man
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #18 on: 09 May 2019, 07:54:06 »

OK, thanks correction, no problem yet, have to remove it first. Is there any typical life time for rear bearing of Omega?

I don't know is it typical, but my originals lasted about 200 000 km and 220 000 km (or at least I could not find any markings that they have been replaced earlier).
Then one re-newed needed to be replaced after 100 000 km. Now I'm waiting was it just bad batch or is the other one also going soon..
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28089
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #19 on: 09 May 2019, 10:04:36 »

My plod was on its original ones at 285k miles, so nearly 500k kms :o

Some people seem to kill them in a third of that :-\
Logged
Onanists always think outside the box.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #20 on: 09 May 2019, 11:31:53 »

Interesting difference, perhaps winter time here in Finland has something to do with it. How well the lubrication works in -20C. However, I still think that my noise is bearing failure. It is not rattling but "croaking". The sound did not change when braking with foot or handbrake so not dragging pads or shoes. 
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28089
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #21 on: 09 May 2019, 12:10:20 »

Did the sound change during left/right cornering?
Logged
Onanists always think outside the box.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #22 on: 09 May 2019, 12:25:24 »

Yes, remember when turning left sound was increasing (in right side). Also it was stronger in certain speed e.g. 40-50 km/t. Could not hear. it as clearly in higher speeds when othe noises increased, too.
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 28089
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #23 on: 09 May 2019, 13:46:03 »

Does indeed sound like a bearing :y
Logged
Onanists always think outside the box.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #24 on: 09 May 2019, 14:50:31 »

Yes, like a worn bearing.
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 909
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Where to Locate Axle Stands (Rear)
« Reply #25 on: 09 May 2019, 16:09:36 »

Actually the hub nut was 32mm... Sedan 2001
Logged
Pages: 1 2 [All]   Go Up
 

Page created in 0.038 seconds with 21 queries.