Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - EMD

Pages: 1 2 3 4 5 6 7 [8] 9 10 11 12 13 14 15 ... 242
106
Car Parts, bits For Sale & Wanted / Re: Clocks wanted
« on: 29 March 2017, 18:24:30 »
Hello , Im after a  V6 speedo/instument panel complete as mine has finally packed up completely now  :(
You'll need to specify age, engine and tyre size ;)

2003  /  2.6  / 235/45/17  :)
Saloon or estate?

Saloon

Im guessing the estate one is not compatible  :-\ :-\

107
General Car Chat / Re: Bending brake pipes ?
« on: 29 March 2017, 18:20:52 »
*edit. Paw singular  ::)

Your doing a great job steve ... have you had a go with a plasma cutter yet  ;)

Ive searched in the shed for the new fuel line for hours then seen it hanging up in a place i thought i would see it easily  ::) Oh and found the special key to undo the hubcaps  ;D Really ought to drop the fuel tank to gain better access to the brake line  :( I shall try the socket method first to shape the bends and see how it goes  :y

108
General Car Chat / Re: Bending brake pipes ?
« on: 28 March 2017, 18:38:51 »
I have made the fuel pipe from the tank to the pipes to engine bay and temporally fitted them onto the rubber pipe but will these fuel pipes need to be flared at each end otherwise i think they will pull out , even with the fuel line clips .

109
General Car Chat / Re: Bending brake pipes ?
« on: 28 March 2017, 18:31:25 »
Thanks folks , i need to replace a few brake pipes and an awkward fuel pipe that runs up near the side of the tank (cav)  :y Surely there must be a pipe bender for these specific jobs , would make it easier .

110
General Car Chat / Bending brake pipes ?
« on: 28 March 2017, 17:58:48 »
Any recommendation for a decent brake pipe bender and flaring tool . I have read somewhere that certain tools brake or dont flare properly  :-\

111
Car Parts, bits For Sale & Wanted / Re: Clocks wanted
« on: 28 March 2017, 17:54:10 »
Hello , Im after a  V6 speedo/instument panel complete as mine has finally packed up completely now  :(
You'll need to specify age, engine and tyre size ;)

2003  /  2.6  / 235/45/17  :)
Saloon or estate?

Saloon

112
General Car Chat / Re: This made you buy a Marina in 1975.
« on: 27 March 2017, 13:40:50 »
Wolseley Saloon , i remember being took out in one and shown how to handbrake turn  ;D Still like the P6 but think i would take the 2.2 rather than V8 as only driving sedately these days  ::)

113
Car Parts, bits For Sale & Wanted / Re: Clocks wanted
« on: 27 March 2017, 13:30:35 »
Is this just  hit and miss to weather a set of replacement clocks will work or not  ??? Whats all this tech2 lark just to swap clocks  :-\

114
Car Parts, bits For Sale & Wanted / Re: Clocks wanted
« on: 26 March 2017, 18:33:13 »
Hello , Im after a  V6 speedo/instument panel complete as mine has finally packed up completely now  :(
You'll need to specify age, engine and tyre size ;)

2003  /  2.6  / 235/45/17  :)

115
General Car Chat / Re: This made you buy a Marina in 1975.
« on: 26 March 2017, 18:16:12 »
Dolly Sprint  :y Went through a brick wall as a passenger in Allegro  :( ::) It did drive home though  :D

116
Car Parts, bits For Sale & Wanted / Clocks wanted
« on: 26 March 2017, 02:01:54 »
Hello , Im after a  V6 speedo/instument panel complete as mine has finally packed up completely now  :(

117
Newbie Welcome Area / Re: another newbie to the forum
« on: 22 March 2017, 14:08:35 »
Welcome to oof  :y

118
Omega Gallery / Re: one or two pictures of the old bus
« on: 22 March 2017, 14:07:02 »
I'm not jealous of the lovely straight panels and gleaming paintwork.. mine looks like scrapyard fodder with all the scratches rust and brick shaped dents over most of the panels courtesy of the local druggie chav scum..

Pictures please  :o :D

119
General Car Chat / Re: Don't look a gift horse in the mouth !
« on: 22 March 2017, 13:58:53 »
Too right , snap that up .. worth a fortune  :y

120
General Car Chat / Re: Any idea how to fix my welder?
« on: 22 March 2017, 13:55:35 »
nah it's not damp or anything and wire looks good. I've got a feeling I forgot to put a tip on it :-[

 ::) ;D

Didn't you get some replacement tips  :-\

Pages: 1 2 3 4 5 6 7 [8] 9 10 11 12 13 14 15 ... 242

Page created in 0.04 seconds with 20 queries.