(head gasket on these is done without removing the chain assembly and timing cover).
I really can't picture how this is done.
How do you remove the head and cams without taking the cam sprockets with it?
Please check the Forum Guidelines at the top of the Newbie section
81
on: 15 April 2024, 14:45:21
|
||
Started by Darth Loo-knee - Last post by Viral_Jim | ||
(head gasket on these is done without removing the chain assembly and timing cover). I really can't picture how this is done. How do you remove the head and cams without taking the cam sprockets with it? |
82
on: 15 April 2024, 14:32:43
|
||
Started by Jim82 - Last post by Jim82 | ||
Hence I always suggest people with GM ones refurb them, rather than replace with crap. Its a bit extra work, but cheaper and will last longer. Is there any easy to spot tell tale that they are original GM? GM logo somewhere? |
83
on: 15 April 2024, 14:27:39
|
||
Started by tomuxzz - Last post by tomuxzz | ||
Perhaps I should have been clearer about the video...No I didn't tried. I created third long video: https://youtu.be/q-fGX4W9tDQ?si=uDNFD65pVkSo1CJN |
84
on: 15 April 2024, 14:16:45
|
||
Started by JamieC2311 - Last post by yousef | ||
I live in Cyprus and have had the same problem.
I got around this problem by removing the switch's put Talcum Powder on it leave it a day then with a soft small paint brush sweep the powder off. I have to do this every two years |
85
on: 15 April 2024, 13:30:41
|
||
Started by yousef - Last post by yousef | ||
Hallo everybody,
I am new at this computer technology so please forgive me if i make mistakes or go to the wrong department. I own 2001 vauxhall omega 2.2 with engine code Z22XE. I love the car but have a problem and hopefully someone at this forum can help. My water hoses were getting a bit hard, did all the test then sent it to have a pressure test. Its come back as cracked cylinder head, can it be repaired or can someone shed a light on where i can get one or even a secondhand one. I am willing to travel anywhere to get this part. By the way i live in Cyprus and will travel to the UK or anywhere. |
86
on: 15 April 2024, 12:57:46
|
||
Started by Varche - Last post by TheBoy | ||
Years ago it used to be normal practice when coming up behind someone you wanted to get past, to give a quick non aggressive flash of the headlights, and more often than not they would move out of the way to let you past.At best they will either flick you the V, or refuse to get in. Or both. |
87
on: 15 April 2024, 12:55:56
|
||
Started by Darth Loo-knee - Last post by TheBoy | ||
Finished a head gasket repair on a friends 1.4 Turbo Zaf C.Yeah, but I bet my Zaf's intakes were shittier than this, LOL |
88
on: 15 April 2024, 12:49:03
|
||
Started by tomuxzz - Last post by Doctor Gollum | ||
Perhaps I should have been clearer about the video...
There's too much back round noise to hear what the engine is doing, if anything, when the rpm spikes. No driving and no radio. Just the rpm and the engine. And for the third or fourth time, have you tried removing and reseating the cluster? |
89
on: 15 April 2024, 12:29:21
|
||
Started by STEMO - Last post by Doctor Gollum | ||
There aren't too many places to divert to in that part of the world... If you want the aircraft back in one piece that is
|
90
on: 15 April 2024, 12:27:21
|
||
Started by tomuxzz - Last post by tomuxzz | ||
You could always look to find somebody good with a soldering iron, the failure mode on the ABS module is a fractured bond wire, in fact two, (as there are two in parallel to increase current handling), not to hard to repair but it is fiddly.Great thanks I will try! And I created another video for rpm problem, Mabey it would more clear. https://youtu.be/tgfxWicssL8?si=s0sWJNb4javBIs4Y |