Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Search the maintenance guides for answers to 99.999% of Omega questions

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - cwill144

Pages: [1] 2 3 4 5 6 7
1
Omega General Help / Re: Omega V6 downpipe gasket
« on: 27 February 2024, 21:40:03 »
It’s a 3.0L and think they are genuine GM downpipes. As only one side is a problem will have to it there is an issue with those flanges.

2
Omega General Help / Re: Omega V6 downpipe gasket
« on: 27 February 2024, 19:14:31 »
I answered the question earlier. I have fitted the genuine ones and the o/s failed. No sealant was fitted. What should it torqued to?
The only other thing I can think is speed bumps causing it. Can you get standard springs as they all seam to be lowered ones. It has eibach ones on it but would rather it standard ones.

3
Omega General Help / Re: Omega V6 downpipe gasket
« on: 26 February 2024, 21:45:16 »
Yes had 1 set but it went on the drivers side. Do you know where I can get them from? Tried at the dealer who said they were discontinued.

4
Omega General Help / Omega V6 downpipe gasket
« on: 26 February 2024, 20:54:22 »
I have had issues with my 3.0L V6 exhaust downpipe gasket. Each time I change the gasket it fine then it starts blowing within about 6 months. I’ve tried different makes of gasket I even had a genuine GM and it still went. I have checked for flatness on the flange and they seam ok.
Can anyone recommend a gasket or a fix? It only seams to be the o/s which would point to the manifold or downpipe flange!! Have a mot in 6 weeks so would like to have a permanent fix.
Any gasket recommendation would be good.

5
Omega General Help / Re: MV6 3.0L exhaust blowing
« on: 27 October 2023, 22:34:42 »
No they are original GM cats, been on the car since I’ve had it. Only had this issue the last 12 months. And I do tighten the same sequence as you say.

6
Omega General Help / MV6 3.0L exhaust blowing
« on: 27 October 2023, 21:07:20 »
I’ve had an issue with one manifold to Down pipe (cat) blowing. I’ve changed the gasket about 3 times now cures the problem and 2-3 months later happens again and gasket has blown. I’ve tried different types of gasket with no luck. One was a genuine GM part.
I’m worried about snapping off a stud if I over tighten it. The flanges look ok but can only assume one isn’t flat as only have the issue on the o/s
An advice would be appreciated

7
Omega General Help / Re: Steering wheel removal
« on: 29 December 2022, 16:08:32 »
Thanks everyone, ordered puller off eBay already arrived, steering wheel came straight off.
Thanks for the advice.

8
Omega General Help / Re: Steering wheel removal
« on: 27 December 2022, 15:38:02 »
Tried a Snap-on puller with no luck. Will order the one off eBay. Thanks

9
Omega General Help / Steering wheel removal
« on: 27 December 2022, 13:55:55 »
I’ve been trying to remove my steering wheel, everything is removed (air bag, nut) but it won’t come off the spline. Have soaked in WD40 any advice on how to get it off would be great!!! Was removed about 3 years ago.

10
Omega General Help / Re: Engine water loss.
« on: 06 November 2022, 01:49:22 »
Pm sent. Thanks for all the advice.

11
Omega General Help / Re: Engine water loss.
« on: 05 November 2022, 16:02:59 »
Thanks for the info, the 2 previous engines one had the big end go, and the other a massive oil leak so changed to the current one. I still have old one in my garage.
When it first over heated it was dry for a couple of weeks, and there were never any wet patches on the ground. The HBV was replaced a couple of years ago along with all the hoses when the engine was fitted and a new radiator.
I will check all the things listed above, but can’t find a leak. Any more ideas would be great.
Thanks

12
Omega General Help / Engine water loss.
« on: 05 November 2022, 13:17:31 »
A few weeks ago I went to London and my 3.0L MV6 overheated.
I topped it up and it has ran fine. But ever since it has been using water.
Can’t find a leak anywhere but needs about 2l of water a week. There is no water in the oil, or oil in the water. Has anyone experienced anything similar on a V6? The only think I can think of is the head gasket and it is burning off the water.
Have already changed the engine twice so if I can’t sort the issue may have to scrap the car.
Thanks.

13
Omega General Help / Re: Clunk from front suspension
« on: 26 June 2022, 14:51:25 »
Goes for MOT next week so will get them to check it over. But has only done 2500 miles in last 2 years, and not driven in winter. So will have a another look but sounds like the struts are correct.

14
Omega General Help / Re: Clunk from front suspension
« on: 26 June 2022, 14:39:11 »
Everything was replaced about a 2 years ago. Have checked on a 4 post lift and nothing is broken. Have checked all bolts and re torqued all of them. Drop links look ok. Is it normal to have the gap under the front strut top hat?

15
Omega General Help / Clunk from front suspension
« on: 26 June 2022, 14:26:25 »
I have had a issue with a rattle from the front of my MV6 when driving on rough roads. It would stop when I touched the brakes. I changed the caliper slide pins that have stopped the rattle. But if I hit a pot hole/drain cover I get a clunk from the front. Should there be a gap below the front strut mount top hat in the engine bay? it is about 5mm. It had Bilstein struts & eibach springs fitted.

Pages: [1] 2 3 4 5 6 7

Page created in 0.024 seconds with 19 queries.