Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Omega Electrical and Audio Help / Re: Cam sensor needed

« on: 14 April 2024, 15:58:53 »

Also, i thought its just the one cam sensor on the V6,

Is this correct?
Or is there one on each bank?

2

Omega Electrical and Audio Help / Re: Cam sensor needed

« on: 14 April 2024, 14:50:38 »

Managed to source a genuine sensor,
Unfortunatley, it has a square plug and not an oval one, I hadn't thought to check first.

Square plugged v6 sensor ready to post if anyone wants it.

3

Omega Electrical and Audio Help / Re: Cam sensor needed

« on: 07 April 2024, 19:56:23 »

Thank you sir.

4

Omega Electrical and Audio Help / Cam sensor needed

« on: 07 April 2024, 12:17:56 »

Where can I source a genuine cam sensor from these days?

Also can anyone tell me if all the V6 ones are the same? Id imagine they are..
Its for a 3.2

5

Omega General Help / Re: Plenum chamber needed , 3.2

« on: 04 April 2024, 19:40:51 »

I've got a spare plenum from a 3.2 if you want to.pm me 

Done, thank you.

Cheers for the info everyone.

6

Omega General Help / Plenum chamber needed , 3.2

« on: 03 April 2024, 21:10:39 »

Am i correct in thinking the later plenum is longer?
Has anyone got one knocking about?

7

Omega General Help / Shift Solenoid PO758

« on: 13 February 2024, 18:40:31 »

I have started getting this code again, once cleared its fine but a few minutes later its back up, with the spanner light on, and i'm limping. Shift solenoid 'B' apparently.
Had this before at the same time as a wiring issue, then i understood it was fixed.

How difficult is this to change? If I took the sump off, what would i be looking at?
This is assuming there are parts available.

8

Omega General Help / Still wont start.

« on: 20 August 2023, 14:00:22 »

So after replacing the starter, and it started fine,
I had a fault code of PO758, shift solenoid
Cleared code and she ran fine. Then the shifter starting acting up, all lights lit up and went in to limp mode.

Now the car wont start at all! as in wont crank, again, So back to square one.

Any ideas?

9

Omega General Help / Re: Car wont turn over

« on: 19 August 2023, 16:02:28 »

Turns out it was the starter. Thanks for the advice guys. 
Not the best job but not the worst either.
Car now showing the spanner light but ill get to that asap.

10

Omega General Help / Re: Car wont turn over

« on: 14 August 2023, 18:40:10 »

No, not dropped keys. The chip in still in there, but then i guess it would spin over and not fire in that case scenario.
I wondered about the inhibitor switch, as the starter is doing nothing, wont even crank the engine slowly.
I shall try the wooden mallet as soon as I can.

Thinking about it, I had a starter put in about four years ago.

11

Omega General Help / Car wont turn over

« on: 13 August 2023, 20:14:20 »

So after running fine, I went to start the car and all I got is a relay click from the engine bay.
If it turned over slowly or starter clicked Id have an idea, but its just dead.

Battery is good.

Where do I start guys?

12

Car Parts, bits For Sale & Wanted / Plenum chamber wanted.

« on: 01 August 2023, 20:10:59 »

Does anyone have one for the later v6 engines?
I need to replace mine due to a previous owners bad Lpg installation.

I haven't enough posts to use the wanted section, My apologes.

13

Omega General Help / Re: 3.2 Thermostat.

« on: 01 August 2023, 20:04:15 »

Thermostat in, Managed to save the pipe in the end.
Thanks for all the advice.

14

Omega General Help / Re: 3.2 Thermostat.

« on: 30 July 2023, 14:52:59 »

So I'm down to the pipe and thermostat, but rain has stopped play.
Seeing as its going to be on hold till saturday, i may aswell get a new pipe.
Thing is, I cant seem to find one, can anyone point me in the right direction?

15

Omega General Help / Re: 3.2 Thermostat.

« on: 26 July 2023, 21:53:37 »

Cheers.
Thermostat on its way. Anyone have a picture of the transfer pipe? I havent started the job yet so no idea what im searching for.