31
Omega General Help / lost key
« on: 20 June 2018, 19:14:03 »
anybody got any great ideas how to remove the ignition barrel without the key ,,,,
thankyou
thankyou
- 27 April 2024, 05:29:58
- Welcome, Guest
News:
Please play nicely. No one wants to listen/read a keyboard warriors rants....
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
32
Omega General Help / Re: lamba sensor fitment
« on: 19 June 2018, 20:53:33 »
HI,,
Thankyou for your effort in putting your car on the ramp . i will now hopefully get the problem sorted
Thankyou for your effort in putting your car on the ramp . i will now hopefully get the problem sorted
33
Omega General Help / Re: lamba sensor fitment
« on: 19 June 2018, 08:47:22 »
ok thankyou,,
do you know if the front and rear lamba sensors are the same
do you know if the front and rear lamba sensors are the same
34
Omega General Help / Re: lamba sensor fitment
« on: 16 June 2018, 19:10:20 »
ok thankyou , the plugs have been moved from original location , so not sure were they belong . were is the guide
please
please
35
Omega General Help / Re: lamba sensor fitment
« on: 16 June 2018, 17:21:09 »
ok thankyou ,,
do you know how to identify which plugs are front and rear
do you know how to identify which plugs are front and rear
36
Omega General Help / lamba sensor fitment
« on: 16 June 2018, 15:10:03 »
Hi,,
the omega has 3.0 cats and down pipes but its a 3,2 . so i need to fit the extra lamba sensors to each bank of down pipes . looking at the position of the lambas i can see its the front sensors that need fitting . which means i will need to remove the down pipe first to fit . so my question is does it matter were the sensors go due to the fact that there is no front cat ...
Thankyou
the omega has 3.0 cats and down pipes but its a 3,2 . so i need to fit the extra lamba sensors to each bank of down pipes . looking at the position of the lambas i can see its the front sensors that need fitting . which means i will need to remove the down pipe first to fit . so my question is does it matter were the sensors go due to the fact that there is no front cat ...
Thankyou
37
Omega General Help / Re: failed mot emissions
« on: 12 June 2018, 13:42:58 »
the car did belong to jamescdx he did the conversion
38
Omega General Help / Re: failed mot emissions
« on: 12 June 2018, 12:00:01 »
Hi,, yes now and again the engine warning light comes on , will it affect the performance missing the sensors
thanks
thanks
39
Omega General Help / Re: failed mot emissions
« on: 12 June 2018, 11:54:29 »
this particular 3.2 omega has got the earlier exhaust and cats fitted from a 3.0 so only uses 2 lambda sensors 
is there any reason somebody would do this
Thankyou
is there any reason somebody would do this Thankyou
40
Omega General Help / Re: failed mot emissions
« on: 12 June 2018, 11:51:12 »
ok thankyou , drivers side coil pack
41
Omega General Help / Re: failed mot emissions
« on: 12 June 2018, 09:47:33 »
HI,, ok passed the mot emissions . but its still misfiring at high rmp it then continues to misfire on what feels like 3-4 cylinders and then as you drive at lower speeds it gradualy comes back on 6 cylinders
any ideas
thankyou
any ideas
thankyou
42
Omega General Help / Re: failed mot emissions
« on: 06 June 2018, 16:49:33 »
ok thanks ,., just tried that and no difference. when you start from cold the engine revs are low. usually when you start from cold the engine revs are higher due to the cold start operating
usually when you start from cold the engine revs are higher due to the cold start operating
43
Omega General Help / Re: failed mot emissions
« on: 06 June 2018, 14:56:34 »
ok thankyou . in that case i will need to buy a new purge valve as the back has broken off it were the pipe connects
44
Omega General Help / Re: failed mot emissions
« on: 06 June 2018, 14:48:42 »
ok thankyou , what does this vacuum sphere do
45
Omega General Help / Re: failed mot emissions
« on: 06 June 2018, 14:38:06 »
it seems to have been bypassed the pipe from the drivers wheel arch goes direct to the bridge will it still run correctly
thankyou
thankyou