Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: 1 2 3 [All]   Go Down

Author Topic: help required please  (Read 4112 times)

0 Members and 1 Guest are viewing this topic.

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
help required please
« on: 11 September 2010, 22:07:15 »

Hi everyone i,ve have a problem with my car,i ave just changed my engine fromma doner car everything runs fine on sart up except the eml stays on. once the engine is warm it has no power and won't rev past 2500 rpm. I hav e changed the maf sensor and the icv, does anyone have a idea of what the problem might be? all responses greatly appreciated.
Logged

tidla

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • solihull
  • Posts: 4097
    • View Profile
Re: help required please
« Reply #1 on: 11 September 2010, 22:08:51 »

what work have you done/ parts replaced?
Logged

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #2 on: 11 September 2010, 22:19:13 »

as above, complete engine change new plugs maf sensor and icv engine ran fine on doner car
Logged

tidla

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • solihull
  • Posts: 4097
    • View Profile
Re: help required please
« Reply #3 on: 11 September 2010, 22:23:32 »

im not into the techie side, sounds like its in limp mode, on the 2.0 motors the cam sensor causes the same thing.
Logged

VX1

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Reading, Berkshire
  • Posts: 2056
    • View Profile
Re: help required please
« Reply #4 on: 11 September 2010, 22:25:38 »

It will be the crankshaft sensor. What was the year of the donor car? Did you use the ecu from your car or the donor car?
Logged
Vx Trade club card holder
Halfords trade card holder

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #5 on: 11 September 2010, 22:36:40 »

i kept same ecu on car for engine,i did think that it might be a crank or cam sensor. but why did it run ok while still ondoner car all wires are connected.
Logged

tidla

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • solihull
  • Posts: 4097
    • View Profile
Re: help required please
« Reply #6 on: 11 September 2010, 22:41:54 »

if the wires are nicely cooked, the jiggin around of engine fitment might have finished them off.
Logged

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #7 on: 11 September 2010, 22:49:08 »

didn't smell any burning of wires only oily smell which is normall after changing a engine
Logged

alank46

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • South Devon
  • Posts: 389
    • 3L Elite Estate 1996
    • View Profile
Re: help required please
« Reply #8 on: 11 September 2010, 22:50:09 »

Hi
Paperclip it for fault codes.
Alan

Quote
Hi everyone i,ve have a problem with my car,i ave just changed my engine fromma doner car everything runs fine on sart up except the eml stays on. once the engine is warm it has no power and won't rev past 2500 rpm. I hav e changed the maf sensor and the icv, does anyone have a idea of what the problem might be? all responses greatly appreciated.
Logged
Elite now gone.  Bought an X-Type 4x4.  If there had been an Omega 4x4 I would have bought that instead.  We really liked the Omega, but I wanted 4x4.

Kneepad

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • West Scotland
  • Posts: 1409
    • View Profile
Re: help required please
« Reply #9 on: 11 September 2010, 22:57:32 »

Logged

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #10 on: 11 September 2010, 23:12:01 »

i may sound thick but have tried reading them but cant seem to understand them. will try again on monday as the mig is not on my drive
Logged

Kneepad

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • West Scotland
  • Posts: 1409
    • View Profile
Re: help required please
« Reply #11 on: 12 September 2010, 00:03:06 »

Quote
i may sound thick but have tried reading them but cant seem to understand them. will try again on monday as the mig is not on my drive


The codes are easier to understand if you watch the video clip that accompanies the instructions.   :y
Logged

weasel

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • norfolk
  • Posts: 40
    • View Profile
Re: help required please
« Reply #12 on: 12 September 2010, 08:37:02 »

Have the plug leads been taken off during engine swap? or maybe the flow and return fuel lines are mixed up?
Logged
To find the limit, first you have to go past it...

Elite Pete

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chester
  • Posts: 19580
  • My spider senses are tingling
    • Audi SQ5 GSX1400
    • View Profile
Re: help required please
« Reply #13 on: 12 September 2010, 09:03:48 »

Quote
Have the plug leads been taken off during engine swap? or maybe the flow and return fuel lines are mixed up?
They are different sizes ;)
Logged
Retired

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #14 on: 12 September 2010, 09:22:00 »

all runs fine when cold it'just won't rev past 2500 when warm
Logged

Elite Pete

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chester
  • Posts: 19580
  • My spider senses are tingling
    • Audi SQ5 GSX1400
    • View Profile
Re: help required please
« Reply #15 on: 12 September 2010, 09:23:34 »

Sound like its in limp mode, you'll need the codes ;)
Logged
Retired

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #16 on: 14 September 2010, 18:33:52 »

right guys i,ve been and read the codes think i did it right it goes 212129493947 hope someone will make sense of that :) ill also add that it will rev to 2000 rpm then drop to a thousand then back to 2000 lightg ondash stays on all the time
Logged

PhilRich

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • A bit further North of the Back of Beyond!
  • Posts: 10338
    • Mk 2 Volvo V70
    • View Profile
Re: help required please
« Reply #17 on: 14 September 2010, 18:47:42 »

Lambda sensors connected correctly? wiring in good nick from sensors to plugs? :-/
Logged
If it ain't broke keep fixing it 'til it is!

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #18 on: 14 September 2010, 18:57:43 »

as far as i know cant see that it will be sensors as ll good before
Logged

RobG

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Bristol
  • Posts: 13831
  • I might have a link, pic or part number for that
    • 16 plate Mokka. Vivaro
    • View Profile
Re: help required please
« Reply #19 on: 14 September 2010, 20:13:58 »

Is the TPS fully connected. :question Do the butterflys open fully when engine not running :question Number 5 injector connected :question
« Last Edit: 14 September 2010, 20:15:04 by RobG »
Logged
All that is necessary for the triumph of evil is that good men do nothing.

UPVC windows/doors/fascias/soffit/gutters supplied/fitted

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #20 on: 14 September 2010, 20:16:39 »

hi i,ve not got drive by wire throttle it is done by cables
Logged

RobG

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Bristol
  • Posts: 13831
  • I might have a link, pic or part number for that
    • 16 plate Mokka. Vivaro
    • View Profile
Re: help required please
« Reply #21 on: 14 September 2010, 20:23:43 »

I know that :) but the 2.5 has a TPS on the throttle body
Logged
All that is necessary for the triumph of evil is that good men do nothing.

UPVC windows/doors/fascias/soffit/gutters supplied/fitted

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #22 on: 14 September 2010, 20:26:01 »

ok i know whatr you mean yes is connected it all run fine in doner car :-/
Logged

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #23 on: 15 September 2010, 21:01:15 »

just another thought would it cause it to do that if the vacum pipes were connected the wrong way ?
Logged

RobG

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Bristol
  • Posts: 13831
  • I might have a link, pic or part number for that
    • 16 plate Mokka. Vivaro
    • View Profile
Re: help required please
« Reply #24 on: 15 September 2010, 21:13:53 »

Logged
All that is necessary for the triumph of evil is that good men do nothing.

UPVC windows/doors/fascias/soffit/gutters supplied/fitted

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #25 on: 21 September 2010, 23:25:40 »

Bit of a update peeps, i took  the pleneum off tonight and it stunk of petrol,i also found that it wasn'tsitting properly. all put back together but still have same problem ,i,ve also noticed that the  chrome pipe in front of the drive belt  gets red hot !! can any one explain why is this??? it has also blown the short  rubber pipe it connects onto,could this be the problem??
Logged

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #26 on: 22 September 2010, 21:04:24 »

Anyone ?????? :-/
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 33813
  • Git!
    • View Profile
Re: help required please
« Reply #27 on: 22 September 2010, 21:11:45 »

Did you connect the plug leads up correctly, particularly the 2-4-6 bank (which is not obvious).

Did you keep the original plenum and throttle pot that matches the ecu(the throttle pot pinout got changed at one point)
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 33813
  • Git!
    • View Profile
Re: help required please
« Reply #28 on: 22 September 2010, 21:16:00 »

Can I also ask that you read the fault codes again as I suspect you have some errors in you numbers above.

I am guessing:

212129493947

is actualy 12 12 12 94 94 94 7.....

So when you read them you will get 3 12's to start and then each fault will flash out three times and read all codes until you get 3 off 12's again


Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 33813
  • Git!
    • View Profile
Re: help required please
« Reply #29 on: 22 September 2010, 21:19:48 »

94 is cam sensor by the way so check all plugs are connected up around the passenger bank
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 33813
  • Git!
    • View Profile
Re: help required please
« Reply #30 on: 22 September 2010, 21:24:25 »

Quote
Bit of a update peeps, i took  the pleneum off tonight and it stunk of petrol,i also found that it wasn'tsitting properly. all put back together but still have same problem ,i,ve also noticed that the  chrome pipe in front of the drive belt  gets red hot !! can any one explain why is this??? it has also blown the short  rubber pipe it connects onto,could this be the problem??

Thats a blocked cat or exhaust centre section
Logged

TestOmega

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Mississauga, Canada
  • Posts: 158
  • Been helped, will help.
    • View Profile
Re: help required please
« Reply #31 on: 22 September 2010, 21:27:42 »

Quote
Bit of a update peeps, i took  the pleneum off tonight and it stunk of petrol,i also found that it wasn'tsitting properly. all put back together but still have same problem ,i,ve also noticed that the  chrome pipe in front of the drive belt  gets red hot !! can any one explain why is this??? it has also blown the short  rubber pipe it connects onto,could this be the problem??
If I am not mistaken those are the exhaust gases coming forward.  There is obviously exhaust pressure (misfires, blockage, failure of the SAI one way valve on the SAI pipe, etc.).  It may be related to your overall stuff but it is quite disturbing!

Should identify which side rubber coupling has been blown and others may help better or have ideas too.

Cheers.

Sorry I believe Marks DTM Calib already addressed it.   :-[
« Last Edit: 22 September 2010, 21:31:47 by TestOmega »
Logged
!!!!!!!!!!!!!!!!!!  May I be blessed to give more than I receive  !!!!!!!!!!!!!!!!!!

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #32 on: 22 September 2010, 22:28:18 »

Thanks for reply yes kept same throttle body and pleneum plug leads all connected when engine was out of car  but will double check, the pipe which blew was on same side above air con pipe. don't think the cats are blocked as it runs fine when engine is cold,how can i check if they are blocked and how can i cure it if they are ? seems like there is plenty of pressure coming out or exhaust. many thanks for all your replys. i may sound stupid but what is the sai again ??? am getting old and can be quite forgetfull ::)
« Last Edit: 22 September 2010, 22:30:04 by 00jonboy »
Logged

TestOmega

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Mississauga, Canada
  • Posts: 158
  • Been helped, will help.
    • View Profile
Re: help required please
« Reply #33 on: 23 September 2010, 00:36:24 »

SAI is Secondary Air Injection.  There is an air pump in near the fron wheel well and under ECU, etc., control it pumps fresh air into the exhaust for emission purposes.  Heats up O2s fast as unburnt stuff gets the cats red hot fast.  There is a one way valve between the right and left rubber couplings to ensure that hot exhaust does not come to the front or flow in the silver pipe at front.  This pipe should remain cool to touch always.  The rubber couplings kind of insulate the middle pipe from connections at exhaust manifolds.

OK I need to cut it out, too much rambling  :-[

Cheers and good luck. :y
Logged
!!!!!!!!!!!!!!!!!!  May I be blessed to give more than I receive  !!!!!!!!!!!!!!!!!!

000jonboy

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • exeter
  • Posts: 40
    • View Profile
Re: help required please
« Reply #34 on: 23 September 2010, 18:20:07 »

it is looking like the cats are buggered then by the looks of it then :( :(
Logged
Pages: 1 2 3 [All]   Go Up
 

Page created in 0.041 seconds with 21 queries.