Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1]   Go Down

Author Topic: Tightening torque of drive shaft to wheet journalismi flange  (Read 2151 times)

0 Members and 1 Guest are viewing this topic.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 906
    • 2.6 Y26SE Elegance 2001
    • View Profile

Cannot find the list of torque anymore, where is it? Is the right torque with old bolts just 50 Nm as in guide here or 50Nm +60+15 degrees what is in GM guide. What to use here?
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 906
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #1 on: 26 May 2019, 08:24:49 »

How to edit the Topic, automatic text correction did something strange, I am talking about Wheel Journal Flange.
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 906
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #2 on: 26 May 2019, 12:38:51 »

Rear bearing job almost jobbed, still missing torque of those six flange bolts, please help.
Logged

ronnyd

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Bury St Edmunds Suffolk
  • Posts: 8591
    • Vectra 1.8 SRI Silver
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #3 on: 26 May 2019, 15:10:59 »

If it,s driveshaft to hub, Haynes says 50nm. Have you got a Haynes, as it goes on to mention 2 further stages of tightening? HTH.
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 906
    • 2.6 Y26SE Elegance 2001
    • View Profile
Logged

ronnyd

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Bury St Edmunds Suffolk
  • Posts: 8591
    • Vectra 1.8 SRI Silver
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #5 on: 26 May 2019, 16:10:52 »

Quote from Haynes, "Driveshaft to hub".
                                Stage1                 50nm
                               Stage2                 Tighten a further 60 deg
                               Stage3                     "        "     "      15deg
Doesn,t mention using new bolts.
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 906
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #6 on: 26 May 2019, 16:21:54 »

OK, then I do it like that as GM says the same, thanks.
Logged

ronnyd

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Bury St Edmunds Suffolk
  • Posts: 8591
    • Vectra 1.8 SRI Silver
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #7 on: 26 May 2019, 16:43:40 »

Good luck. :y
Logged

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 906
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #8 on: 26 May 2019, 17:03:16 »

Thanks, perhaps they all snap as not new...
Logged

biggriffin

  • Omega Lord
  • *****
  • Offline Offline
  • huntingdon, Hoof'land
  • Posts: 9736
    • Vectra in a posh frock.
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #9 on: 26 May 2019, 17:31:49 »

Ft, with a blob of loctite
Logged
Hoof'land storeman.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 906
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #10 on: 26 May 2019, 17:45:17 »

Sorry but what means Ft?
Logged

biggriffin

  • Omega Lord
  • *****
  • Offline Offline
  • huntingdon, Hoof'land
  • Posts: 9736
    • Vectra in a posh frock.
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #11 on: 26 May 2019, 20:10:25 »

Sorry but what means Ft?

Foooking tight.
Logged
Hoof'land storeman.

polilara

  • Senior Member
  • ****
  • Online Online
  • Gender: Male
  • Finland
  • Posts: 906
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #12 on: 27 May 2019, 07:24:45 »

OK, nice to learn new things.
Logged

ronnyd

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Bury St Edmunds Suffolk
  • Posts: 8591
    • Vectra 1.8 SRI Silver
    • View Profile
Re: Tightening torque of drive shaft to wheet journalismi flange
« Reply #13 on: 27 May 2019, 16:24:16 »

OK, nice to learn new swear words ;)
FTFY
Logged
Pages: [1]   Go Up
 

Page created in 0.035 seconds with 22 queries.