- 28 April 2024, 20:14:03
- Welcome, Guest
News:
Search the maintenance guides for answers to 99.999% of Omega questions
1
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 18:27:03
|
||
Started by grifter - Last post by grifter | ||
As I'm planning to give the rear donut bushes a go is it better to do this while I've got the diff lowered for the rear springs or should I put that back up and then do the bushes?
|
2
on: Today at 18:02:58
|
||
Started by Varche - Last post by dave the builder | ||
Omega was £415 to tax so that's gone up £20
Still .... at least the council will have that cash to fix all the bloody pot holes car insurance renewal £100 too much (compared to other sites) so I'll have to waste my time arguing them down again |
3
on: Today at 17:41:43
|
||
Started by Varche - Last post by countrywoman | ||
Come south to Malvern, nice here apart from the slow drivers.
|
4
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 17:13:24
|
||
Started by grifter - Last post by Tick Tock | ||
My flanges were so crusty, I fitted these after a tidy up with the angle grinder.
https://www.ebay.co.uk/itm/174475765263?chn=ps&_ul=GB&_trkparms=ispr%3D1&amdata=enc%3A1NJ-5UZY-T4iGZc9gpthWXg66&norover=1&mkevt=1&mkrid=710-134428-41853-0&mkcid=2&mkscid=101&itemid=174475765263&targetid=1816181028179&device=c&mktype=pla&googleloc=1006790&poi=&campaignid=19090194174&mkgroupid=147009364227&rlsatarget=aud-1162782600376:pla-1816181028179&abcId=9303860&merchantid=137662815&gad_source=1&gclid=CjwKCAjw57exBhAsEiwAaIxaZoAG_oBqEh6XPZznyRGHlKNTsgEiNryVljEiTj_ZGbi7F7xJB1-tNhoC9HkQAvD_BwE Obviously you would need to check the cat pipe diameter. |
5
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 16:37:23
|
||
Started by grifter - Last post by grifter | ||
If you have time, get yourself some good TiN coated drill bits. Far tougher that ordinary HSS bits. Thanks will have a look, any recommended makes? Andy |
6
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 16:36:38
|
||
Started by grifter - Last post by grifter | ||
Facelift saloon self levelling springs with ident LA are GM part no. 90295666 Cheers, I got the other ones on order but I'm still keen to find genuine, if I can find them and afford them. |
7
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 16:35:31
|
||
Started by grifter - Last post by grifter | ||
Does it still have SL? I take it you mean self levelling? The compressor runs sometimes but I don't think it's doing much if anything. There is a pipe going to the back shocks but they aren't actually connected into anything so I'm assuming it's now defunct. Need to get a set of drill bits as I looked at the manifold and there is no way I'm attempting to take all that out with the car 1 inch above my nose, and also risk snapping more studs. Any recommendations for good set of drills don't want to buy chinese stuff? Cheers Andy |
8
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 15:53:22
|
||
Started by grifter - Last post by ronnyd | ||
If you have time, get yourself some good TiN coated drill bits. Far tougher that ordinary HSS bits.
|
9
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 15:50:43
|
||
Started by grifter - Last post by johnnydog | ||
Facelift saloon self levelling springs with ident LA are GM part no. 90295666
|
10
on: Today at 15:48:29
|
||
Started by Andy H - Last post by TheBoy | ||
And they will all need replacing again in the next decade or so, when 2G is sunsetted.
|