Hmmm - LA is VX90295666, and it's listed in my 2000 EPC as being for Senators with engines 25NE, 30NE, C30LE, C30NE, C30SE WITHOUT self levelling.
It's also listed as OmegaB Saloon (except Police and Armoured Body) WITH self levelling, from chassis number W1081185 onwards. However my EPC is from year 2000, so doesn't cover much on facelift Omega B's or 3.2's.
- 28 April 2024, 21:21:48
- Welcome, Guest
News:
Search the maintenance guides for answers to 99.999% of Omega questions
1
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 20:53:32
|
||
Started by grifter - Last post by LC0112G | ||
2
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 18:27:03
|
||
Started by grifter - Last post by grifter | ||
As I'm planning to give the rear donut bushes a go is it better to do this while I've got the diff lowered for the rear springs or should I put that back up and then do the bushes?
|
3
on: Today at 18:02:58
|
||
Started by Varche - Last post by dave the builder | ||
Omega was £415 to tax so that's gone up £20
Still .... at least the council will have that cash to fix all the bloody pot holes car insurance renewal £100 too much (compared to other sites) so I'll have to waste my time arguing them down again |
4
on: Today at 17:41:43
|
||
Started by Varche - Last post by countrywoman | ||
Come south to Malvern, nice here apart from the slow drivers.
|
5
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 17:13:24
|
||
Started by grifter - Last post by Tick Tock | ||
My flanges were so crusty, I fitted these after a tidy up with the angle grinder.
https://www.ebay.co.uk/itm/174475765263?chn=ps&_ul=GB&_trkparms=ispr%3D1&amdata=enc%3A1NJ-5UZY-T4iGZc9gpthWXg66&norover=1&mkevt=1&mkrid=710-134428-41853-0&mkcid=2&mkscid=101&itemid=174475765263&targetid=1816181028179&device=c&mktype=pla&googleloc=1006790&poi=&campaignid=19090194174&mkgroupid=147009364227&rlsatarget=aud-1162782600376:pla-1816181028179&abcId=9303860&merchantid=137662815&gad_source=1&gclid=CjwKCAjw57exBhAsEiwAaIxaZoAG_oBqEh6XPZznyRGHlKNTsgEiNryVljEiTj_ZGbi7F7xJB1-tNhoC9HkQAvD_BwE Obviously you would need to check the cat pipe diameter. |
6
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 16:37:23
|
||
Started by grifter - Last post by grifter | ||
If you have time, get yourself some good TiN coated drill bits. Far tougher that ordinary HSS bits. Thanks will have a look, any recommended makes? Andy |
7
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 16:36:38
|
||
Started by grifter - Last post by grifter | ||
Facelift saloon self levelling springs with ident LA are GM part no. 90295666 Cheers, I got the other ones on order but I'm still keen to find genuine, if I can find them and afford them. |
8
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 16:35:31
|
||
Started by grifter - Last post by grifter | ||
Does it still have SL? I take it you mean self levelling? The compressor runs sometimes but I don't think it's doing much if anything. There is a pipe going to the back shocks but they aren't actually connected into anything so I'm assuming it's now defunct. Need to get a set of drill bits as I looked at the manifold and there is no way I'm attempting to take all that out with the car 1 inch above my nose, and also risk snapping more studs. Any recommendations for good set of drills don't want to buy chinese stuff? Cheers Andy |
9
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 15:53:22
|
||
Started by grifter - Last post by ronnyd | ||
If you have time, get yourself some good TiN coated drill bits. Far tougher that ordinary HSS bits.
|
10
Omega Help Area / Omega General Help / Re: Rear springs elite and broken middle section exhaust studs
on: Today at 15:50:43
|
||
Started by grifter - Last post by johnnydog | ||
Facelift saloon self levelling springs with ident LA are GM part no. 90295666
|