Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Radar

Pages: 1 [2] 3 4 5 6 7 8 9 ... 93
16
Meetings, gatherings, parties etc / Re: High Wycombe Autumn Meet
« on: 09 October 2015, 10:32:06 »
Thankyou gentlemen.
 
Tony i was gutted i couldn't make the last one but it was unavoidable due to being abroad on business

I am presuming you remove the switch from the inside of the car as opposed to from underneath? - i don't mind "experimenting" on the day!!

17
Meetings, gatherings, parties etc / Re: High Wycombe Autumn Meet
« on: 08 October 2015, 21:32:13 »
I am going to try and make it (in my old elite) if that is ok Tony  :P  - I would appreciate some pointers on the gear selector cleaning process - still don't grasp the realignment bit. Will get some switch cleaner - is anything else needed? Thankyou.

P.S. A Tech 2 session would be great too!

18
Thanks Rob :y

19
A Paperclip test threw up a knock signal circuit 1(16) and telltale (checklight) voltage low (135).

A couple of days ago a new brake light bulb was replaced so I am not sure if this is related to 135?

Does the 16 code mean a new knock sensor or is it a red herring?

Any advice would be appreciated.

P.S. The symptoms of slow acceleration have not happened for the last week despite being driven every day.

20
Thanks - have read the guide but am not understanding the realignment bit - will read again after a not so long day.


21
Omega General Help / Re: Complete new key
« on: 07 September 2015, 21:11:12 »
The lost key has been found!

Thankyou to all who shared their wisdom :y

22
I started the car and it was not the battery light but the engine management light on - also noticed the gear selector lights flashing like a xmas tree when moving from p to d.

Before i could do a paperclip test my brother needed to go to London, so will have to do it another time.


23
Thanks for the heads up :y

24
Omega General Help / Re: Complete new key
« on: 04 September 2015, 21:16:47 »
This may be of use to someone in the future:

Part Number
M VZ16510    Lower horseshoe key - (i.e. blank blade cut with immobiliser chip) - 61.00+
M V0009146043  Sender Radio Control(i.e. main internals incl. 3 button rubber fob and new batt.) - 35.60+ 
M ZPROG            Key Programme - 49.50+

Will be popping in to chat to local keycutting shops

25
Brother called me and says the car struggles to get up to 20mph and the red battery light is on. Its happened a few times. Just drove car again and its ok? I'm afraid I don't have multimeters etc.. but does anyone know if this is more likely to be battery or alternator issue. I will look at the car this weekend but any pointers appreciated!

26
Omega General Help / Re: Complete new key
« on: 02 September 2015, 23:03:50 »
Thankyou for all the pointers - I will do some more investigating :y

27
Omega General Help / Re: Complete new key
« on: 02 September 2015, 22:44:30 »
Thanks - so could I take the key to a standard key cutting shop to get a copy or is that just to naïve of me?

28
Omega General Help / Re: Complete new key
« on: 02 September 2015, 22:27:56 »
Thankyou - we still have one full working key (this was the "spare" before the "main" key was lost) - I will pop to the stealers and see what they quote.

29
Omega General Help / Re: Complete new key
« on: 02 September 2015, 00:07:02 »
Thanks I will look into this but I have just come across this and wondered if this would be programmable?

http://m.ebay.co.uk/itm/VAUXHALL-3-BUTTON-CAR-REMOTE-CONTROL-KEY-FOB-ALARM-GOOD-WORKING-ORDER-/301636833030?nav=SEARCH

30
Omega General Help / Complete new key
« on: 01 September 2015, 22:39:56 »
It's been a while since I've been on but my brother has my old Omega and has lost his 3 button key.

I am after a complete key with blade, little chip / all innards and a cut blade - is there a one stop shop for this as I cannot seem to find stores that do the inners or cut the blade. Might someone have an old key that I could get reprogrammed?

I understand it would need a tech 2 session. I have the car pass.

Thanks!

Pages: 1 [2] 3 4 5 6 7 8 9 ... 93

Page created in 0.021 seconds with 19 queries.