Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

31

Omega General Help / multi-ram testing

« on: 01 February 2011, 22:35:26 »

My front multi-ram doesn't operate and I want to check a few things before I spend the day on it tomorrow. 

With engine off should I be able to suck and blow through the vac pipe that goes to the front ram ie though the solenoid or should the solenoid block the flow.

Also Is checking the voltage supply as simple as +12v/ 0v  switching.

I should add the multi-ram operates if I put a vacuum to it so its not seized or sticky

Thanks

32

Omega General Help / Help from someone with epc please

« on: 20 June 2010, 20:38:04 »

As title could someone give me the part nos for a couple of bits please.   I can't get to dealers and there useless with descriptions.

I need vx nos for the following

sill cover clips/buttons


sill cover end cap clips


and rear inner arch trim clip


Thanks
Lee

33

Omega General Help / CODE 61 HELP

« on: 19 September 2009, 14:51:08 »

Im getting a code           61   Fuel Tank Ventilation Valve Voltage Low
does anone have any ideas what i can do to get rid of it??

It was fine last time i drove the car but its been off the road for a couple of weeks with the plenum and leads removed.  Put new leads on and fired up today with this code.   I've reset it a couple of time and it keeps coming back so it is current.
Any help or advice welcome.
Lee

34

Omega General Help / V6 PLUG LEADS

« on: 29 August 2009, 20:03:48 »

Does anybody know what aftermarket leads are best(or at least the same lenth) for the v6 as every set ive tried so far seem to be too long.
TIA
lee

35

Omega General Help / Engine mounts and gearbox

« on: 05 July 2009, 22:35:01 »

Could anyone tell me if the engine mounts are the same for the 2.0 and the v6 and also what bhp the 2.0 manual gearbox can handle as i think i may have just broke one or the other.
Thanks
Lee

36

Omega General Help / Help from someone with epc please

« on: 16 May 2009, 22:38:36 »

Could anyone please check part no  93173680 for me and tell me if its for 1 head or both.
TIA
lee

37

Omega General Help / cam locking tool

« on: 28 March 2009, 21:50:40 »

Just a quicky I'm going to get myself a cam locking kit for the v6  and was wondering if the sealey  vse130 was ok as eveyone recons the laser one isn't very good.   Also whats the differance between the vs130 and the vse130 apart from price.
Thanks
Lee

38

Omega General Help / Oil cooler reliability

« on: 14 March 2009, 21:38:49 »

Hope someone can help me on this am i right in thinking the original coolers were not stainless hence the problems and the new ones are stainless. If so would the stainless one be expected to last forever. Reason i'm asking is i think mine has been replaced already and if the stainless ones dont fail then it saves me a job, if they do still fail then im just going to change it whilst i've got it stripped down.
lee

39

Omega General Help / oil cooler and cam cover gaskets

« on: 11 March 2009, 00:08:14 »

Can any one confirm that the part no's are the same for all v6 engines and if the thermostat comes with the housing.
Thanks
Lee

40

Omega General Help / Rear subframe bushes

« on: 12 September 2008, 22:50:15 »

I need to replace mine and i remember reading a while back (cant find with search) that there are two different types normal and heavy duty.

Does anyone have a part no for the heavy duty ones please as my local stealer only lists one and its probably not the ones i want.
TIA
lee

41

Omega General Help / Black sealant

« on: 27 June 2008, 21:41:10 »

Just got cam gasket and sealant for 2.0xev and vx supplied me with sealant part no 93165267 which is in a 80ml plastic tub (short culking gun type tube) it is black but could someone in the know please confirm this is the corect sealant.
I think they've given me the work shop stuff as it says "not intended to be passed on to private consumers in the first line of the label.
TIA
lee

42

Omega General Help / [m by=hotel21 destboard=omegaelectric dest=1209070861]: Interior wiring loom

« on: 24 April 2008, 22:01:01 »

[moved] [link=http://www.omegaowners.com/forum/YaBB.pl?num=1209070861/0]ICE and Omega Electrical[/link] [move by] hotel21.

43

Omega General Help / Cruise control

« on: 05 April 2008, 20:58:17 »

Two questions.
1.  Can the clutch switch be bypassed to check if it works before i buy a switch
2. Is there any taletell that cruise is being used ie light on dash ect

lee

44

Omega General Help / Display (mid)

« on: 22 March 2008, 19:11:51 »

What makes the display work.  does it just take all the info from the normal sensors or does it have seperate ones and does it need a different ecu to a car that doent have all the functions.
Ie if i put the display and stalk into a gls will it have the range, temp,cons,ect or does it need to talk to tech 2 to get them to work.
lee

45

Omega General Help / Upgrading interior/ wiring loom

« on: 23 March 2008, 19:22:59 »

I am currently trying to upgrade my interior from gls cloth spec no side airbags/heated seats ect to cdx leather with side airbags heated seats ect and the wiring for these funtions are not already connected to the multiplugs that go to the seats.
Does anyone know if the wiring will be there and just not connected (ie just taped up somewhere) or do i have to change or add to the loom.
Both cars are of the same year and saloons  but one is a 2.5 cdx auto and mine is a 2.0 gls manual.
TIA Lee

edit  also wiring for rear electric windows