Omega Owners Forum

Chat Area => General Discussion Area => Topic started by: Elite Pete on 19 July 2008, 19:43:32

Title: Thanks Pete and Mark
Post by: Elite Pete on 19 July 2008, 19:43:32

Thanks to Pete (Matchless) for spending his day replacing my crankshaft oil seal and MarkDTM for the tech 2 work oh and not forgetting a thank you to their better halves for the tea and biscuits.

Thanks :y

Title: Re: Thanks Pete and Mark
Post by: Marks DTM Calib on 19 July 2008, 19:45:36

So, what was the fuel consumption!

Title: Re: Thanks Pete and Mark
Post by: Jimbob on 19 July 2008, 19:47:36

Quote

So, what was the fuel consumption!

4 cups of tea and 6 biscuits  ;D

Title: Re: Thanks Pete and Mark
Post by: TheBoy on 19 July 2008, 19:51:25

Ah, the crank oil seal.  Requiring the use of a rather great bit of angle iron, and a rather great torque wrench?

Title: Re: Thanks Pete and Mark
Post by: Elite Pete on 19 July 2008, 20:00:45

Quote

Ah, the crank oil seal.  Requiring the use of a rather great bit of angle iron, and a rather great torque wrench?

I'll say, i've not seen one as big as Pete's before ::)

Title: Re: Thanks Pete and Mark
Post by: Elite Pete on 19 July 2008, 20:01:51

Quote

So, what was the fuel consumption!

Its not going to be too good ::)

I couldn't help myself ;D

Title: Re: Thanks Pete and Mark
Post by: Jimbob on 19 July 2008, 20:02:48

Quote

Quote

Ah, the crank oil seal.  Requiring the use of a rather great bit of angle iron, and a rather great torque wrench?

I'll say, i've not seen one as big as Pete's before ::)

It is a monster!

Title: Re: Thanks Pete and Mark
Post by: Darth Loo-knee on 19 July 2008, 20:05:13

Its just the way I'm standing ;D

Title: Re: Thanks Pete and Mark
Post by: Elite Pete on 19 July 2008, 20:15:31

Quote

Quote

Quote

Ah, the crank oil seal.  Requiring the use of a rather great bit of angle iron, and a rather great torque wrench?

I'll say, i've not seen one as big as Pete's before ::)

It is a monster!

Its a two hander :o

Title: Re: Thanks Pete and Mark
Post by: Marks DTM Calib on 19 July 2008, 20:53:12

Matchless did all the wrenching and Pete all the talking

Title: Re: Thanks Pete and Mark
Post by: Matchless on 19 July 2008, 23:08:10

Quote

Matchless did all the wrenching and Pete all the talking

Not quite, Im an Engineer but when theres tight things to undo I hand the bar to someone more qualified....ie heavier.  :)

Title: Re: Thanks Pete and Mark
Post by: TheBoy on 20 July 2008, 09:50:20

Quote

Quote

Matchless did all the wrenching and Pete all the talking

Not quite, Im an Engineer but when theres tight things to undo I hand the bar to someone more qualified....ie heavier.  :)

You should have called me then  :-[

Title: Re: Thanks Pete and Mark
Post by: Elite Pete on 20 July 2008, 09:59:22

Quote

Quote

Quote

Matchless did all the wrenching and Pete all the talking

Not quite, Im an Engineer but when theres tight things to undo I hand the bar to someone more qualified....ie heavier.  :)

You should have called me then  :-[

I bet you are a couple of stone behind me ::)

Title: Re: Thanks Pete and Mark
Post by: TheBoy on 20 July 2008, 10:09:35

Quote

Quote

Quote

Quote

Matchless did all the wrenching and Pete all the talking

Not quite, Im an Engineer but when theres tight things to undo I hand the bar to someone more qualified....ie heavier.  :)

You should have called me then  :-[

I bet you are a couple of stone behind me ::)

Its a 2 man job, which means 2 fattys required  ;)