Omega Owners Forum

Chat Area => General Discussion Area => Topic started by: mick-1975 on 13 March 2009, 17:41:15

Title: would these work
Post by: mick-1975 on 13 March 2009, 17:41:15

  my dad has a set of alloys for sale of his bmw, but there 17 inch ,
 (ignore the bmw badge in middle )just wondering weather these would look good on my mig ???
(http://i193.photobucket.com/albums/z101/mick-1975/001.jpg)  
if the holes line up ? :y

Title: Re: would these work
Post by: nick v6 on 13 March 2009, 17:46:45

not sure if they would even fit properly

plus hate that style rim sorry :-/

Title: Re: would these work
Post by: mick-1975 on 13 March 2009, 17:49:13

Quote

not sure if they would even fit properly

plus hate that style rim sorry :-/

 no prob , ive seen a set on a vectra sri that look nice

Title: Re: would these work
Post by: nick v6 on 13 March 2009, 17:52:45

Quote

Quote

not sure if they would even fit properly

plus hate that style rim sorry :-/

 no prob , ive seen a set on a vectra sri that look nice

make sure that sit on the hubs right
ive seen loads of alloys go on cars and the wheel is to big for the hubs

if its only slightly to big for your hubs you can get plastic rings that sit on the hub :y

Title: Re: would these work
Post by: mick-1975 on 13 March 2009, 17:55:49

  looking at them and the ones i have , i think the gap between the tyre and arch would be to big and not look right ,

Title: Re: would these work
Post by: cem_devecioglu on 13 March 2009, 18:16:31

Bmw PCD (5*120)  is very different than the Omega (5*110) ..Wont fit.. unless you use a PCD convertor..

Title: Re: would these work
Post by: vauxmad on 13 March 2009, 18:22:50

not a chance with out hub adapters and then they would stick out too much, just buy some replicas if you really like the style

Title: Re: would these work
Post by: cem_devecioglu on 13 March 2009, 18:27:04

but if you have some close friends in steel-iron machining shops who have enough time , may be :-/

Title: Re: would these work
Post by: mick-1975 on 13 March 2009, 18:28:26

thanks , i shall keep what i have at the moment ,
   :y  did,nt think they would fit

Title: Re: would these work
Post by: unlucky mark mv6 on 14 March 2009, 19:18:46

wouldent like the job of cleaning the buggers mate.

Title: Re: would these work
Post by: Mr Skrunts on 14 March 2009, 21:00:03

Quote

wouldent like the job of cleaning the buggers mate.

Easiest job in the world.

Let some chemicals soak in and

[media]http://www.youtube.com/watch?v=ZVK6dAUJ6hc[/media]

Title: Re: would these work
Post by: Vamps on 14 March 2009, 21:33:16

I like that idea, is it a wheel cleaning brush or just something adapted, either way it would make life simpler. :y :y
Might have a little look on ebay later, see I can get a bargain ;) ;)

Title: Re: would these work
Post by: tmx on 14 March 2009, 23:07:05

 also the griffin centre caps off MV6 wheels fit in the BMW ones  :y :y well they MV2's and standard E46 alloys but i bet they fit all of them

get some MV2 replica's or M3 Antracite replicas