Omega Owners Forum

Chat Area => General Discussion Area => Topic started by: Martin_1962 on 21 August 2006, 23:12:37

Title: That place - someone needs my help!
Post by: Martin_1962 on 21 August 2006, 23:12:37
Well I had a quick nose - bit quiet but someone needs my help on LPG

Unfortunately for them I am not a member

Can someone tell them to google for omega lpg diy and follow the link at the bottom of the review!!!!
Title: Re: That place - someone needs my help!
Post by: jonny2112 on 22 August 2006, 00:46:39
Not sure if we should.................. [smiley=undecided.gif]
Title: Re: That place - someone needs my help!
Post by: x25xe on 22 August 2006, 08:57:26
I am still a member and occasionally look around.  Have not posted once since this forum was started ;D

What was the title of the thread and I will direct accordingly.
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 22 August 2006, 09:06:13
Dual Fuel was on the thread title
Title: Re: That place - someone needs my help!
Post by: x25xe on 22 August 2006, 10:55:11
OK will reply.

I think that I have already spotted it just a moment ago - Marks DTM has replied.
Title: Re: That place - someone needs my help!
Post by: x25xe on 22 August 2006, 10:59:01
Just done - I searched myself and posted the link up.

Nice review if I may say - I wish I had the skills to do a conversion on mine!
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 22 August 2006, 11:27:29
Sneaky!!!!
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 22 August 2006, 11:28:01
Quote
Just done - I searched myself and posted the link up.

Nice review if I may say - I wish I had the skills to do a conversion on mine!

It is not THAT difficult - just needs patience and care.
Title: Re: That place - someone needs my help!
Post by: x25xe on 22 August 2006, 11:32:00
I reckon that I could cope with the wiring and the evaporator fitment - it is just the drillings for the injectors along with the filler neck that scares me off somewhat.
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 22 August 2006, 12:43:41
If you know someone with a 6.5mm twist drill and a pillar drill it is easy - I just used carE and a B&D. I did screw one hole up - this became the pressure sensor hole.

They need to be very close to the inside due to the slope of the intakes.

Filler - fix it to a towbar!
Title: Re: That place - someone needs my help!
Post by: Marks DTM Calib on 23 August 2006, 14:12:03
A stack of that post has now been deleted!
Title: Re: That place - someone needs my help!
Post by: tunnie on 23 August 2006, 14:13:35
on the other site? why!

I am sure they will find the light and register here  ;)
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 23 August 2006, 14:57:25
Quote
A stack of that post has now been deleted!

I see so that forum thinks that any help outside of itself is of no use?

What a bunch of sad cases!

I am considering joining with a new name and a throwaway email address and PMing all the victims!
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 23 August 2006, 14:58:01
Quote
on the other site? why!

I am sure they will find the light and register here  ;)

They need to find here!

How come that site blocked MIGWEB?
Title: Re: That place - someone needs my help!
Post by: Marks DTM Calib on 23 August 2006, 15:51:12
I dont know...

There is a guy on MIG putting an LS1 into an Astra coupe (5.7 V8)....very impressive, hes making it rear wheel drive to and using an Omega rear setup (diff, trailing arms etc)
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 23 August 2006, 16:47:47
Quote
I dont know...

There is a guy on MIG putting an LS1 into an Astra coupe (5.7 V8)....very impressive, hes making it rear wheel drive to and using an Omega rear setup (diff, trailing arms etc)

Has anyone LS1ed an Omega though - it would be easier!
Title: Re: That place - someone needs my help!
Post by: Marks DTM Calib on 23 August 2006, 17:15:53
If somebody donated an engine then I would be happy to try it!

It realy is a quality job hes doing though, fantastic bit of fabrication work.
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 23 August 2006, 18:27:18
Quote
If somebody donated an engine then I would be happy to try it!

It realy is a quality job hes doing though, fantastic bit of fabrication work.

Would one fit in mine!
Title: Re: That place - someone needs my help!
Post by: Martin_1962 on 23 August 2006, 18:39:18
Quote
Just done - I searched myself and posted the link up.

Nice review if I may say - I wish I had the skills to do a conversion on mine!

Noticed you've been threatened

Now is it worth a ban?

If I was still a member I'd do it for a laugh!