Omega Owners Forum

Newbie Area => Newbie Welcome Area => Topic started by: malcolm1973 on 21 November 2010, 18:43:29

Title: new member
Post by: malcolm1973 on 21 November 2010, 18:43:29

just to say hi on my 3rd omega but this one not sure as hve afew probs ,2.5 elite 2000 model, cracking looking car, but cuts out when cold when you give quick blip on accelarator, and at front of engine has a little thin plastic pipe with rubber elbow loose ,one end goes into where the the 2 intake pipes go to ,and power steering stiff when on full turn then the same other way but ok when in mid turn ??? so i have joined here hoping i may sort this out as dont want to sell it as love the car with all the toys ,,,, :'(

Title: Re: new member
Post by: vauxfan2k on 21 November 2010, 19:05:15

Hello and welcome, I see you are from my birthtown,  :y

Title: Re: new member
Post by: Lizzie_Zoom on 21 November 2010, 19:06:21

Hello and a warm welcome to you! :y

Title: Re: new member
Post by: waspy on 21 November 2010, 19:19:14

How do & welcome to the OOF :y :y

Title: Re: new member
Post by: Welung666 on 21 November 2010, 19:33:18

Welcome to OOF Malcolm :y

Title: Re: new member
Post by: The Red Baron on 21 November 2010, 19:37:07

welcome to the forum malcolm :y

Title: Re: new member
Post by: Kneepad on 21 November 2010, 20:02:00

Hello Malcolm, welcom to the forum.   :y

Post your query in the Omega General Help section.

Title: Re: new member
Post by: Dishevelled Den on 21 November 2010, 20:34:38

How do you do Malcolm, welcome along. :y :y

Title: Re: new member
Post by: Jimbob on 21 November 2010, 20:34:49

Hello & Welcome  :y

Title: Re: new member
Post by: NF on 21 November 2010, 20:38:13

Hi Malcolm
Welcome to the forum

Title: Re: new member
Post by: Entwood on 21 November 2010, 20:42:00

"Hello" and Welcome :)

Title: Re: new member
Post by: malcolm1973 on 21 November 2010, 21:13:13

found where the other end of plastic pipe goes ,,as was dangling down behind radiator and front of engine,, just behind ram dual intake there is 2 other rubber pipes going into like a black plastic cylinder with which has meant to have 3 piece on top but looked like a t piece as mine had snapped of hope this helps someone  :-? other end was on like a diaphram at top front of engine

Title: Re: new member
Post by: Cliffo B on 21 November 2010, 21:26:46

Hello Malcolm,welcome to the Forum :y

Title: Re: new member
Post by: maria on 21 November 2010, 21:26:50

Hello and welcome to the forum :y

Title: Re: new member
Post by: symes on 21 November 2010, 22:53:02

Hi & Welcome to OOF :y

Title: Re: new member
Post by: mindaz on 22 November 2010, 00:01:35

hi Malcolm , welcome  ;)

Title: Re: new member
Post by: Seth on 22 November 2010, 09:44:26

Welcome bud! :y

Title: Re: new member
Post by: dbug on 22 November 2010, 10:26:30

Welcome to OOF mate  :y

Title: Re: new member
Post by: Jusme on 22 November 2010, 10:52:07

Hi Malcolm, Welcome to the OOF..  ;)

Title: Re: new member
Post by: Cav9_4 on 22 November 2010, 10:53:32

Hi & welcome to the forum :y

Title: Re: new member
Post by: Omega_Dan on 22 November 2010, 12:19:51

welcome to the OOF :y

Title: Re: new member
Post by: PhilRich on 22 November 2010, 13:03:53

Hello & welcome to the OOF  :y

Title: Re: new member
Post by: philnohair on 22 November 2010, 18:20:04

Hi and welcome Malcolm.
I've got a 2000 2.5 Elite which I've had for six and a half years but never had your problem and I'm technically inexperienced so I can't help, sorry.
You are undoubtedly in the right place to get help though, so good luck!

Title: Re: new member
Post by: sandune on 22 November 2010, 22:52:21

Hiya  welcome to the forum :y

Title: Re: new member
Post by: Elite Pete on 23 November 2010, 09:02:50

Hi Malcolm and welcome ;)

Title: Re: new member
Post by: wingman on 23 November 2010, 15:58:38

Hi and a warm welcome  to OOF

Title: Re: new member
Post by: jonnycool on 24 November 2010, 16:23:54

Hi Malcolm, welcome to the forum  :y

Title: Re: new member
Post by: Mr Skrunts on 24 November 2010, 22:48:45

Hi, welcome to the forum.   :y

Title: Re: new member
Post by: Elitenut on 27 November 2010, 09:52:05

Hello and welcome to the Forum. :y