Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: Craig_R on 05 June 2007, 11:02:07
-
With everyone going to the lakes this weekend i thought i would ask this early as i dont want to be stuck changing a few bits this weekend coming.
I need acouple of Torque Settings
Rear Shocks (If I do Them)
WishBones
Track Rods Both ends
Brake Disks
Steering Idler (If I Need to do it)
I know there are acouple of settings on the forum, IE brake stuff.
Thanks :y :y
-
Hi there
I shall look in Haynes tonight after work if no one els posts them. :y
-
Recommended Torque Values
Caution
Angle specifications refer to yield limit controlled fastening bolts, which may only be used once. Tighten fastening bolts only with the appropriate torque and then turn further by the specified angle.
Nm
Exhaust gas recirculation valve and front bracket to auxiliary aggregates holder
20
Airbag unit to steering wheel
8
Outer tie rods to centre tie rod
60
Electro-hydraulic converter to steering gear
2.9
Retaining bow, fluid reservoir to spring strut dome
7
Retaining strap on power assisted steering pump
20
Retaining shackle to cylinder block
20
Bracket, hydraulic modulator to front frame side member
10
Bracket, idler to front frame side member
55 + 75° + 15°
Brackets, cooling loop to strut
4
Power assisted steering hydraulic lines to power assisted steering pump
28
Power assisted steering hydraulic lines to power assisted steering pump (diesel engine)
37.5
Clamp bolt to steering gear
22
Clamp bolt to steering shaft
22
Steering gear to front frame side member
55
Steering wheel to steering shaft
20 1)
Steering arm to steering shaft
160
Steering column with bracket to bulkhead
22
Idler to bracket
60
Centre tie rod to steering arm
60
Centre tie rod to idler
60
Engine damping block
40
Nut, bracket – steering column support
22
Auxiliary aggregates holder to cylinder block
40
Power steering pump to support (X 20 DTH)
20
Power assisted steering pump to auxiliary aggregates holder (4 cylinder engine)
25
Power assisted steering pump to auxiliary aggregates holder (6 cylinder engine)
20
Belt pulley to power assisted steering pump
20
Return line to engine transport shackle
4
Tie rod end to steering knuckle
60
Tie rod end to centre tie rod
60
Steering column support to bracket
22
Sleeve nut, power assisted steering hydraulic lines to screwed socket
18
Sleeve nut, power assisted steering hydraulic lines to steering gear
28
Front exhaust pipe
20
Heat shield to upper steering gear
8
Heat shield to lower steering gear
15
Hydraulic unit heat shield to holder
8
--------------------------------------------------------------------------------
1 ) Tighten fastening nut to 20 Nm/15 lbf. ft., then release by 90° and re-tighten to 20 Nm/15 lbf. ft.
Hope this helps DC 8-)
-
Also:::::
Recommended Torque Values – Brakes
Caution
Angle specifications refer to yield limit controlled fastening bolts, which may only be used once. Tighten fastening bolts only with the appropriate torque and then turn further by the specified angle.
Nm
Cover plate to steering knuckle (front wheel brake)
4
Brake servo to support (nuts)
21
Front brake caliper to brake carrier
30
Rear brake caliper to semi-trailing arm
80
Brake disc to front or rear wheel hub (lock bolt)
4
Bracket to steering knuckle
95 + 30° + 15 1)
Brake backing plate to rear axle
4
ESP pressure sensor to hydraulic modulator
20
Bleeder screw to brake caliper
9
Yaw rate/acceleration sensor to retaining plate
8
Parking brake lever to vehicle underbody (bolts)
20
Bracket for hydraulic modulator to front frame side member
10
Propshaft centre bearing bracket to vehicle underbody
20
ABS/TC control unit bracket to hydraulic modulator
8
Brake master cylinder to brake servo
22
Rear exhaust pipes to catalytic converter
25
Banjo bolt, brake pressure hose to brake caliper
40
Hydraulic modulator to bracket (nuts)
8
Fork lock nut to brake servo piston rod
21
Centre exhaust pipes to catalytic converter, V6
25
Pedal axle to pedal support
18
Pedal support to bulkhead
20
Wheel to wheel hub
110
Wheel sensor to rear differential
8
Wheel bolts to front/rear wheel hub
110
Parking brake telltale switch to parking brake lever
2.5
ABS/TC control unit to bracket
1.5
Union nut to intake manifold
18
Union nuts for all brake lines
16
Hydraulic modulator heat shield to bracket
8
--------------------------------------------------------------------------------
1) Insert new fastening bolts with locking compound.
:-*
-
and for good measure_____
Recommended Torque Values
Caution
Torque values deal with yield limit-controlled retaining screws which may be only be used once. Only tighten retaining screws to the appropriate torque and then continue to tighten by the amount specified.
Nm
Drive shaft to wheel journal flange
50 + 60° + 15°
Brake calliper to semi-trailing arm
80
Brake disc to wheel hub
4
Brake carrier to semi-trailing arm
50 + 30° + 15°
Damping blocks to vehicle underbody
65
Damping blocks to rear axle body
90 + 30° + 15°
Cover on locking differential housing
14
Single disc joint to propshaft flange M10 x 1.25 (Torx)
50 + 45° + 15°
Single disc joint to propshaft flange M12 x 1.5
95
Single disc joint to transmission/rear differential flange M10 x 1.25 (Torx)
50 + 75° + 15°
Single disc joint to transmission/rear differential flange M12 x 1.5
95
Bracket to rear differential
90 + 45° + 15°
Bracket to vehicle level control sensor
4
Centre bearing bracket
22
Centre bearing bracket to vehicle underbody
20
Bracket with level control sensor to rear axle body
12
Bracket with compressor to wheel well
12
Rear differential, rear, to front axle body
90 + 30° + 15°
Rear differential, front, to rear axle body
100 + 75° + 15°
Rear differential cover to rear differential
60
Rear axle body damping bushing to vehicle underbody
125
Clamps to auxiliary control arm
15
Level control system compressor to bracket
4
Swing arm to semi-trailing arm
20
Wheel on wheel hub
110
Wheel sensor on transmission cover
7
Wheel journal flange to wheel journal
3001)
Semi-trailing arm to rear axle body
100
Headlamp range control sensor to rear axle body
10
Stabiliser to rear axle body
22
Shock absorber to semi-trailing arm
110
Shock absorber fastening nut on piston rod
20
Strut for rear axle body to vehicle underbody
65
Ring gear to differential/limited slip differential M10
75
Ring gear to differential/limited slip differential M12
115
Closure bolt of the rear differential
22 + 90° + 180°
Front muffler to catalytic converter
25
Auxiliary control arm to rear axle body
901)
Auxiliary control arm to semi-trailing arm
45
--------------------------------------------------------------------------------
1) use new self-locking fastening nut
DC :y
-
Glad to see Dave has done a great job, just wanted to see if this works, new to photobucket :-? scaned from 1994 to 1999 haynes manual.
(http://i191.photobucket.com/albums/z57/lynsfotobucket/torqueset1.jpg)
(http://i191.photobucket.com/albums/z57/lynsfotobucket/torqueset2.jpg)
-
WOW thanks dave c and Omegalyn
I have all the Torque settings i need to strip the car now :y :y :y
Thanks Again :)
Craig
-
WOW thanks dave c and Omegalyn
I have all the Torque settings i need to strip the car now :y :y :y
Thanks Again :)
Craig
Our pleasure...
DC