Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: Chaoslord on 07 July 2009, 21:12:46
-
Hi.
Just did a paperclipstunt on my Omega B X20XEV, and the result was a 0335 (10,3,3,5), and from what i can see, that is a cranckshaft sensor reporting something.
Anyone have any experience with this error?
The reason i did the diagnostic in the first place was that I often experience a misfire and loss of enginepower, followed by the enginesymbol on the dash.
Can anyone give me some advise?
Chaos
-
yeah, cranksensor. Easy if no a/c, fiddly if you do
-
No A/C, so that makes it a non-fiddly bit then, eh?
Anywhere I can find some instructions?
Chaos
-
So, is the crancksensor fault the reason my car is acting up?
Supah
-
Anyone?
-
So, is the crancksensor fault the reason my car is acting up?
Supah
Yes.
It's mounted on the crankcase just forward of your
oil dipstick tube.
Seeing as you have no AirCon you can do it in two ways.
Either:
1)Undo single dipstick attachment bolt, remove dipstick tube,
block hole in crankcase to stop anything falling in,
change sensor from top.
Or:
2) Jack car up, insert axle stand, change it from underneath.
The cable runs up from the sensor attached to built-in
clips on the Cambelt Cover and joins a connector near
to your alternator. Suggest you re-route the bottom
third, where it goes behind your power steering pump,
and bring it round the front of your power steering pump,
and then reclip it on the original route up and over your
cam cover. This will stop it giving a direct run for oil
drips and condensation to track down, enter the sheath
that covers the final section, collect on your sensor and
cook and crack it.
In my opinion, this is what makes the sensor on the 4 pots
fail, where as it's the heat on the 6 pots.
Hope that helps.
-
Thanks for that detailed procedure, and for the re-routing advise.
I still fail to see why this crankshaft sensor causes a misfire and loss of power though. But then again, I am no car wiz, so I'll take your word for it :)
Chaos
-
Thanks for that detailed procedure, and for the re-routing advise.
I still fail to see why this crankshaft sensor causes a misfire and loss of power though. But then again, I am no car wiz, so I'll take your word for it :)
Chaos
Crankshaft sensor tells the ECU where the rotational position of the crank is .... this is directly related to the position of the valves and pistons... the ECU uses this information to decide when to send fuel in vis the injectors, and when to send the spark to ignite that fuel.
If the information from the crank sensor is corrupt/wrong then the fuel and ignition timing goes all to pot....
If information is missing the engine stops. Dead.
-
Ah, that makes sense. Thank you.
Is this a dangerous condition to keep driving in? Does it damage the engine in any way?
Chaos
-
as written in another post i have similar symptoms. no dead engine tho!
Anyone got any photos to help with this situation?
unfortunately i have a/c so might be a bigger pain!
-
Well, the enginge isn't dead. I just experience a loss of power for a second or two, then it's back and running again, allthough with the enigne warning light.
As I plan to drive around 1000km this summer, i would like to know if this condition damages the engine in any way.
Anyone?
Chaos
-
my engine has been damaged, the head's coming off tomorrow. Don't know yet if it's related to the faulty crankshaft sensor. That had worn wiring which might've caused some shorts in other electrics.. yet to find out fully.
All signs are toward HG failure so we'll have to see :(
-
Well, the enginge isn't dead. I just experience a loss of power for a second or two, then it's back and running again, allthough with the enigne warning light.
As I plan to drive around 1000km this summer, i would like to know if this condition damages the engine in any way.
Anyone?
Chaos
Just change the crank sensor then problem solved, would'nt risk having to drive 1000k with it being dodgy, as it will probably at some stage start cutting out altogether, which is'nt very nice, this has happened to me, just get it changed :y
-
Ok, thx for the info.
Guess I'll be doing some auto-repair before we leave, eh? ;)
Chaos
-
So, is the crancksensor fault the reason my car is acting up?
Supah
Yes.
It's mounted on the crankcase just forward of your
oil dipstick tube.
Seeing as you have no AirCon you can do it in two ways.
Either:
1)Undo single dipstick attachment bolt, remove dipstick tube,
block hole in crankcase to stop anything falling in,
change sensor from top.
Or:
2) Jack car up, insert axle stand, change it from underneath.
The cable runs up from the sensor attached to built-in
clips on the Cambelt Cover and joins a connector near
to your alternator. Suggest you re-route the bottom
third, where it goes behind your power steering pump,
and bring it round the front of your power steering pump,
and then reclip it on the original route up and over your
cam cover. This will stop it giving a direct run for oil
drips and condensation to track down, enter the sheath
that covers the final section, collect on your sensor and
cook and crack it.
In my opinion, this is what makes the sensor on the 4 pots
fail, where as it's the heat on the 6 pots.
Hope that helps.
Fancy writing a maintenence guide then :P