Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: Shark1e on 25 November 2010, 15:04:03
-
Just failed on both outer track rod ends and hand brake.
Adjusted via hole in disc but not holding on the offside.
Replaced rear discs.pads.and shoes a few months back. Really poor setup unless i have fitted shoes incorrectly? Can you fit them wrong?
Or is there a special setup way of the handbrake
Thanks
rob
-
Follow the maintenance guide to the letter :y
-
Take the disc off and check everything is as it should be with the h/brake shoes. It has been mentioned on here that, with some shoes, it is possible for the friction lining to break up.
-
Thanks but what maintainance guide????
Frictions will be checked but been poor sincelast year. Hence replacing them. Really stuck her
-
Thanks but what maintainance guide????
......
This one http://www.omegaowners.com/forum/YaBB.pl?num=1259003779
(http://i84.photobucket.com/albums/k17/Tiff4327/maintguide.jpg)
-
Might be a problem with the linkage in that case.
Try getting someone to work the h/brake while you look underneath to see if its moving....
-
+1 Djac could well be a seized cable
-
don't forget when you adjust the star adjuster thing, to get the same action (tightening or slackening), the star adjuster on one side of the car will need turning the opposite way (up/down) to the opposing side.
It's actually the same way, but just seems different because you're on the other side, does that make sense?
You could end up slackening it when you're trying to tighten it and vice versa.
-
suspect the mechanism is seized one side. Check the maint guide, as others suggest :y
-
Thanks all.
Ok done all the guide says except slaken cable off first then tighten up after. All was free and greasedand star adjusted.
Is the cable looped? or adjusted each side? Cant see pix on my mobile.
Ta rob
-
Thanks all.
Ok done all the guide says except slaken cable off first then tighten up after. All was free and greasedand star adjusted.
Is the cable looped? or adjusted each side? Cant see pix on my mobile.
Ta rob
?????? :-/ :-/ :-/ Sorry but I do not understand. You MUST slaken the cable off first at the yoke linkage under the car before you can adjust the brakes at the wheels ;) ;)
In my experience, and that of others, you cannot adjust the handbrake operation properly without doing it in that sequence ::) ::)
-
Yep, the cable needs to be slack to ensure that you can get max travel on the shoe actuator levers.
If you dont do this then your wasting your time :y
-
sorry a bit clearer my end,
when i replaced the discs, pads and shoes i did not slacken the cable off or adjust it, i thought you just adjusted via holes in disc/drum etc, so i will now have to start from the start in the morning as i'm still at work right now, thanks all
rob
-
sorry a bit clearer my end,
when i replaced the discs, pads and shoes i did not slacken the cable off or adjust it, i thought you just adjusted via holes in disc/drum etc, so i will now have to start from the start in the morning as i'm still at work right now, thanks all
rob
Yep, that should do the trick Rob :y :y
-
oops got the fail sheet back and the motor to find handbrake didn't fail but just an adviser or it, it only failed on the track rod ends,
got them local for £13 each and changed them, but as i had to do it on the drive and in the dark after work friday, i must have miss counted them going back on, so had to get the tracking set sat morn before the MOT, all done now apart from handbrake setup, but did get the tyre fitter to wind off some of the handbrake for me,
did notice no heat shields on my 2.5 tractor is this norm? or are they only of the v6?
rob