Omega Owners Forum

Omega Help Area => Omega Electrical and Audio Help => Topic started by: paul36uk on 11 February 2008, 09:50:51

Title: ncdc 2015
Post by: paul36uk on 11 February 2008, 09:50:51

hi all,i have a 2001 omega mv6 saloon with a 2015 head unit,i have just got hold of a bose amp for it ,does anyone know which new leads or looms i need to get or any other advice i will need to get the job done?

many thanks

Title: Re: ncdc 2015
Post by: Marks DTM Calib on 11 February 2008, 10:00:03

You need the main loom that runs from the drivers kick panel to the Bose amp.

Plus the rear shelf speakers.

And you might want to swap the door speaker out as they are 2ohm instead of 4 so the amp can drive them a bit harder.

Then the head unit needs Tech2ing in order to put it into Bose mode.

Was the 2015 factory fit?

Title: Re: ncdc 2015
Post by: paul36uk on 11 February 2008, 10:33:04

yes it is a factory fit 2015,ive got four bose door speakers too,i know i need to get two rear subs,
do you know where i can get a loom?

cheers

Title: Re: ncdc 2015
Post by: Marks DTM Calib on 11 February 2008, 10:42:45

Quote

yes it is a factory fit 2015,ive got four bose door speakers too,i know i need to get two rear subs,
do you know where i can get a loom?

cheers

From any breaker with bose fitted, it is a seperate loom.

Title: Re: ncdc 2015
Post by: paul36uk on 11 February 2008, 11:06:03

would the loom have to be from a facelift or ar the connections to the amp the same?

Title: Re: ncdc 2015
Post by: Marks DTM Calib on 11 February 2008, 11:13:04

Quote

would the loom have to be from a facelift or ar the connections to the amp the same?

From all the ones I have seen, they are the same.

Title: Re: ncdc 2015
Post by: paul36uk on 11 February 2008, 11:16:09

many thanks for your help  :y

Title: Re: ncdc 2015
Post by: zirk on 11 February 2008, 15:12:27

Hi Paul,

Welcome to the Site. A lot better in here!

Zirk (Chris)

Title: Re: ncdc 2015
Post by: TheBoy on 11 February 2008, 15:51:27

Quote

Quote

would the loom have to be from a facelift or ar the connections to the amp the same?

From all the ones I have seen, they are the same.

I'm guessing the saloon/estate looms vary, but not prefacelift/facelift.

Title: Re: ncdc 2015
Post by: paul36uk on 11 February 2008, 18:48:35

do i have to remove the headunit to acess the connections or are they in the drivers well like someone kindly said?
sorry im no mechanic

Title: Re: ncdc 2015
Post by: Marks DTM Calib on 11 February 2008, 18:53:29

Quote

do i have to remove the headunit to acess the connections or are they in the drivers well like someone kindly said?
sorry im no mechanic

There in the drivers footwell......the dash loom is the same for bose/non-bose

Title: Re: ncdc 2015
Post by: paul36uk on 11 February 2008, 19:17:12

i dont suppose by any chance the loom is already installed at the factory?

Title: Re: ncdc 2015
Post by: Marks DTM Calib on 11 February 2008, 19:21:20

No, only on Bose systems, hence why its a seperate mini loom that only does bose  :y

Title: Re: ncdc 2015
Post by: paul36uk on 11 February 2008, 19:22:41

cheers mark