31
Omega General Help / Re: EGR cheater x30xe (motronic)
« on: 30 January 2016, 17:45:25 »
Ok thank you...when you make some pics let me know!
- 16 June 2024, 15:47:53
- Welcome, Guest
News:
Welcome to OOF
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
32
Omega General Help / Re: EGR cheater x30xe (motronic)
« on: 29 January 2016, 18:39:46 »
Yes i understand man...Could i get many error codes if timing belt was 1 tooth out on the left head on both camshafts (cylinder 2 4 6) ??
Yes baggers sealing correctly..however i will dissasemble the "hand" on which egr stand and see if its stuck...i read some topics that oven cleaner helps...
Yes baggers sealing correctly..however i will dissasemble the "hand" on which egr stand and see if its stuck...i read some topics that oven cleaner helps...
33
Omega General Help / Re: EGR cheater x30xe (motronic)
« on: 27 January 2016, 23:10:52 »
I send you pm stephen.....my wires go like this
A brown grey(white)
B brown green
C brown yellow
D blue black
E red blue
A brown grey(white)
B brown green
C brown yellow
D blue black
E red blue
34
Omega General Help / Re: EGR cheater x30xe (motronic)
« on: 27 January 2016, 17:27:21 »
Yes..getting code 129 egr voltage low...i tried to dissasemble it...the valve moves up and down so it isnt stuck
35
Omega General Help / Re: EGR cheater x30xe (motronic)
« on: 27 January 2016, 16:14:55 »
I think you didnt understand me...i have x30xe engine...but want to put z22se egr cheater...and now i ask if it works?
36
Omega General Help / Re: EGR cheater x30xe (motronic)
« on: 27 January 2016, 15:34:12 »
Yes..but hovewer i want to outfunction egr 
37
Omega General Help / EGR cheater x30xe (motronic)
« on: 27 January 2016, 13:02:57 »
Getting all sorts of error codes including 73 74 maf error....TPS error.and so on..all tried on other car and it works..so i assume i have faulty egr because im also getting code 129 low voltage...does somebody know does cheater for z22se works? If not which one works?
I came upon this thread:
www.omegaowners.com/forum/index.php?topic=104638.msg1364767#msg1310258
Some info on that?
I came upon this thread:
www.omegaowners.com/forum/index.php?topic=104638.msg1364767#msg1310258
Some info on that?
38
Omega General Help / Re: Multiram valve number 2...(behind the coilpack)
« on: 14 January 2016, 02:03:32 »
Thank you
39
Omega General Help / Multiram valve number 2...(behind the coilpack)
« on: 13 January 2016, 21:21:12 »
What is natural position of multiram valve after 4000 rpm? Should it remain in position for example when engine is off or should it operate in direction of coilpack? (opening or closing inlet)
40
Omega General Help / Re: Compression results 3.0 mv6
« on: 09 December 2015, 20:23:43 »
Thank you guys
41
Omega General Help / Re: Compression results 3.0 mv6
« on: 08 December 2015, 19:15:00 »
Its nice to know that ...so there is no need for warm engine test? As i see on internet different readings up to
225 psi or whatsoever
225 psi or whatsoever
42
Omega General Help / Compression results 3.0 mv6
« on: 08 December 2015, 14:18:57 »
Just made compression test yesterday on cold engine and got following
Cyl.
2 10.8 bar
4 10.4 bar
6 10.5 bar
5 10.5 bar
3 10.4 bar
1 10.5 bar
For relevance 10.5 bar is 153 psi..is it good or bad....engine has 90 000 miles...
Cyl.
2 10.8 bar
4 10.4 bar
6 10.5 bar
5 10.5 bar
3 10.4 bar
1 10.5 bar
For relevance 10.5 bar is 153 psi..is it good or bad....engine has 90 000 miles...
43
Omega Electrical and Audio Help / Re: X30xe few errors
« on: 12 October 2015, 16:58:30 »
If we speak about signal VSS its from speedo to ecu..however i connected it and no joy...blocked egr,no joy either...ill try new leads and sparks...engine is idling on 5 cylinders sometimes going on 4...coilpack tested,condition good...
44
Omega Electrical and Audio Help / Re: X30xe few errors
« on: 09 October 2015, 16:17:12 »
I didnt weld it.. I left it as original,connected to exhaust..however i didnt connect VSS signal to ecu..can it affect engine idling and performance? Cause i have symptoms of bad maf and bad coilpack,and i have read that ecu can cause this because off not getting the VSS signal..maf and coilpack are tested and working good..
45
Omega Electrical and Audio Help / X30xe few errors
« on: 01 October 2015, 14:58:42 »
As you know i transplanted x30xe to calibra..i menaged to bypass the immobiliser..however when i start engine(cold) i got EML staying on after 15 seconds of car working...i get following codes in this particular order when doing paper clip test
12 - initiation of diagnosis
135 - tail light,this is not connected in calibra so its normal to be registered
46 - secondary air injection pump,also not connected in calibra..i welded holes on exhaust manifolds
-----------------''''----
17 -knock sensor circuit 2
129 - egr voltage low
63- inlet manifold valve 1 voltage high
73 - maf sensor voltage low
Car is running like shit,stuttering in neutral and when driving,giving a puff of black smoke when hitting throttle...other than that there is no blue or white smoke at least....
12 - initiation of diagnosis
135 - tail light,this is not connected in calibra so its normal to be registered
46 - secondary air injection pump,also not connected in calibra..i welded holes on exhaust manifolds
-----------------''''----
17 -knock sensor circuit 2
129 - egr voltage low
63- inlet manifold valve 1 voltage high
73 - maf sensor voltage low
Car is running like shit,stuttering in neutral and when driving,giving a puff of black smoke when hitting throttle...other than that there is no blue or white smoke at least....