46
Omega General Help / Re: TC and ABS
« on: 15 February 2013, 14:30:00 »
Thats interesting Footloose, it was the front nearside I replaced a tie rod on just before this started, perhaps I need to take a look.
- 28 May 2024, 20:20:21
- Welcome, Guest
News:
Welcome to OOF
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
47
Omega General Help / Re: TC and ABS
« on: 15 February 2013, 11:46:56 »
Bloody cars 
I go out this morning and the TC and ABS lights are on solid and no speedo and car with a spanner(is that EML?) I get home dig out lappy connect up to Omega turn on and no TC ABS lights, I found the ABS and TC tests under the chassis section but it didnt throw up any faults, I found some tests where I think you can test each wheel speed, is it worth getting a mate to hold lappy and go for a drive and test these or not, or do I just need to test it when I have the ABS and TC lights lit up.
Thinking about it I may have made a schoolboy error by clearing the stored fault codes from when the lights where on earlier before I went into the Chassis section, when ABS TC come on next time I will not clear them before going into chassis section and having a look in there.
I go out this morning and the TC and ABS lights are on solid and no speedo and car with a spanner(is that EML?) I get home dig out lappy connect up to Omega turn on and no TC ABS lights, I found the ABS and TC tests under the chassis section but it didnt throw up any faults, I found some tests where I think you can test each wheel speed, is it worth getting a mate to hold lappy and go for a drive and test these or not, or do I just need to test it when I have the ABS and TC lights lit up.Thinking about it I may have made a schoolboy error by clearing the stored fault codes from when the lights where on earlier before I went into the Chassis section, when ABS TC come on next time I will not clear them before going into chassis section and having a look in there.
48
General Discussion Area / Re: A nice new home for my Omega's - Build Thread
« on: 13 February 2013, 14:17:41 »
Great thread, I was just wondering about the bloke who buys your house in 60 years time and decides to clear the back garden to grow some carrotts, man will he be cursing you for "over engineering" 
49
Omega General Help / Re: TC and ABS
« on: 13 February 2013, 13:07:44 »
Ok Albitz thanks, I did have a quick look in some of the other sections but just skimmed through 1 or 2 cant remember which, I will have a thorough look through them all when I hook it up next but might be tomorrow, I will report back with any other findings.
50
Omega General Help / Re: TC and ABS
« on: 13 February 2013, 12:24:40 »
Is it definitley the ABS/ECU Andy and not the wheel sensor ?
51
Omega General Help / Re: TC and ABS
« on: 13 February 2013, 12:14:40 »
I haven't had the ABS and TC lights come on together for about a week, today I plugged an OBDII code reader that connects to a laptop into my mig and I saved this out to file
"My Naff Code Reader" 100219a - PC based diagnostic tool
hkj
"My Naff Code Reader" - KW2000 Communication Window> 2001|Omega-B|Engine|Y 26 SE
Keyword #1: EF
Keyword #2: 8F
Normal timing parameter set.
VIN: W0L0VBM6911051778
vehicleManufacturerECUHardwareNumber 09173199 AA
systemSupplierECUHardwareNumber: BOS 01200261206490
systemSupplierECUSoftwareNumber: 1037360515
systemSupplierECUSoftwareVersionNumber: 0D41
exhaustRegulationOrTypeApprovalNumber: B01003
systemNameOrEngineType: Y26SE
RepairShopCodeOrTesterSerialNumber: Not programmed
ProgrammingDate: 20001027
Identifier: 2020
CalibrationDate: 21130401
CalibrationEquipmentSoftwareNumber: 0602
ECUInstallationDate: V-Car 0006
VehicleManufacturerSpecific: 0261206490
Total number of fault codes: 3
U2108 - CAN-Bus no Communication with ABS/TC
(04) - Not present
P0500 - Vehicle Speed Sensor Malfunction
(04) - Not present
P0500 - Vehicle Speed Sensor Malfunction
(0C) - Not present
I cleared the codes and ran the test again and it came up with no fault codes, is it still looking like a dodgy ABS ECU ?
"My Naff Code Reader" 100219a - PC based diagnostic tool
hkj
"My Naff Code Reader" - KW2000 Communication Window> 2001|Omega-B|Engine|Y 26 SE
Keyword #1: EF
Keyword #2: 8F
Normal timing parameter set.
VIN: W0L0VBM6911051778
vehicleManufacturerECUHardwareNumber 09173199 AA
systemSupplierECUHardwareNumber: BOS 01200261206490
systemSupplierECUSoftwareNumber: 1037360515
systemSupplierECUSoftwareVersionNumber: 0D41
exhaustRegulationOrTypeApprovalNumber: B01003
systemNameOrEngineType: Y26SE
RepairShopCodeOrTesterSerialNumber: Not programmed
ProgrammingDate: 20001027
Identifier: 2020
CalibrationDate: 21130401
CalibrationEquipmentSoftwareNumber: 0602
ECUInstallationDate: V-Car 0006
VehicleManufacturerSpecific: 0261206490
Total number of fault codes: 3
U2108 - CAN-Bus no Communication with ABS/TC
(04) - Not present
P0500 - Vehicle Speed Sensor Malfunction
(04) - Not present
P0500 - Vehicle Speed Sensor Malfunction
(0C) - Not present
I cleared the codes and ran the test again and it came up with no fault codes, is it still looking like a dodgy ABS ECU ?
52
General Car Chat / Re: time to nuke miggy
« on: 08 February 2013, 10:22:07 »
Have they written the classic "I wish my wife was this dirty"
53
Omega General Help / Re: A couple of issues I have...
« on: 07 February 2013, 11:06:00 »1. Brilliant, thanks
2. Any idea how i do that?
Here you go mate http://www.omegaowners.com/forum/index.php?topic=90620.msg1155537#msg1155537
54
Omega General Help / Re: TC and ABS
« on: 06 February 2013, 18:56:46 »Just modified my post above as you were posting yours.
55
Omega General Help / Re: TC and ABS
« on: 06 February 2013, 18:47:40 »
Absolutley no chance it's the sensor ?
56
Omega General Help / Re: TC and ABS
« on: 06 February 2013, 18:38:39 »
An hour after getting my heating working I went out and noticed both TC and ABS and car with a spanner thru it lights were on and speedo wasnt working, so looks like my ECU was on the way out, the car starts and drives ok and everything else works ok, what are my options chaps considering I am broke.
57
Omega General Help / Re: Flushing Heater matrix
« on: 06 February 2013, 13:39:47 »
Finally got round to flushing the matrix and my cabin is like the proverbial sauna now 
thanks guys
thanks guys
58
Omega General Help / Re: misfire
« on: 05 February 2013, 20:41:00 »
My scuttle was leaking like a waterfall, as Tunnie said sillicone the joint, I also sealed the joint from underneath with a couple of strips of Denso tape and it leaks no more
60
Omega General Help / Re: Flushing Heater matrix
« on: 26 January 2013, 13:33:14 »
Thanks, will 1 litre of anti freeze be enough.