1
Omega Electrical and Audio Help / Re: NCDC 2013 cd changer issue
« on: 07 March 2009, 13:50:17 »
do you happen to have a NCDC 2013 for spares that you would like to sell?
- 04 November 2025, 03:02:25
- Welcome, Guest
News:
Welcome to OOF
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Omega Electrical and Audio Help / Re: NCDC 2013 cd changer issue
« on: 07 March 2009, 07:45:15 »
cheers mate, now to find a donor ( easier said than done!!)
3
Omega Electrical and Audio Help / NCDC 2013 cd changer issue
« on: 06 March 2009, 17:14:46 »
hi all, ive got the bose NCDC 2013 in my v6, the CD changer will not read any cd it just keeps saying no disc even when there is 4 in there, ive run a CD cleaner thru but to no avail. any thoughts people. cheers. Nick
4
Omega Electrical and Audio Help / Re: alright what have i done?
« on: 23 September 2007, 08:18:48 »
i replaced my dash bulbs with a nice set of white LEDs.
looks the dogs nadgers
looks the dogs nadgers
5
Omega General Help / Re: Facelift Diff pinion seal
« on: 06 March 2009, 15:55:17 »
thanks and sorry about pic!
6
Omega General Help / Facelift Diff pinion seal
« on: 06 March 2009, 15:31:55 »
Hi all, my 3.0 facelift has a leaky diff, the bit where the prop goes in, is the seal an easy job (eg something i could do) ive looked in haynes and it says something about measuring something before refiting??
any thoughts or tips gratefully appreciated.
Nick
any thoughts or tips gratefully appreciated.
Nick
7
Omega General Help / Re: water flush when to stop
« on: 01 June 2008, 18:08:41 »
If you can, get hold of some swarfega oil and grease remover from halfords, it disolves oil and is perfect for cooling systems, just fill with water and coolant (cheap) then just before it fils up add the swarfega degreaser then run for a while, drain and refil with 50-50 mix of coolant and water job done. ive used it twice now with no trouble.
HTH
HTH
8
Omega General Help / Re: Head Gasket Blown ???????????
« on: 10 September 2007, 16:54:15 »
does the 2.0 have a heater bypass valve as on the V6??
if so i would change this first as this will produce the symptoms you are getting.
sorry im not familiar with the 2.0 ecotech engine bay.
if so i would change this first as this will produce the symptoms you are getting.
sorry im not familiar with the 2.0 ecotech engine bay.
9
Omega General Help / Re: 3 ltr V6 elite problem.
« on: 04 November 2007, 10:40:28 »
try unplugging the crank sensor and plugging it back in again, sounds daft i know but mine was cutting out as yours was and i tried it all, ICV, leads plugs dis pack( they were bieng replaced anyway) i took the crank plug, disconnected it plugged it back in and no more probs.
not sure why but there you go.
not sure why but there you go.
10
Omega General Help / Re: V6 ICV
« on: 06 November 2007, 15:58:44 »Quote
On mine there's a small torx bolt hidden underneath that needs to be undone before you can remove the ICV.
dead right there, mine has one too
extension bar in from the side to reach it.
11
Omega General Help / Re: Dash Illumination
« on: 30 October 2007, 14:28:01 »
go on fleabay or similar and get a set of LEDs for the omega, blue red or white (depending on your taste) and they will never blow again!! i did mine with white and they look great!
HTH
HTH
12
Omega General Help / Re: 3.0 LPG conversion
« on: 02 November 2007, 09:12:09 »
the kit used in the thread (link posted above) looks pretty comprehensive, as far as i can see you need to get a tank, of which there ar a few on ebay, and maybe a spare inlet manifold to play with, instead of mucking up the one on the car, kit is not bad price either, imo
13
Omega General Help / Re: 3.0 LPG conversion
« on: 01 November 2007, 17:03:22 »
very interesting mate, i will be watching with intrest, its about 45/50 minutes to Alton from here so yes we are quite close. i think there are probably more members near me than i realize!!!!
cheers for info. Nick
cheers for info. Nick
14
Omega General Help / 3.0 LPG conversion
« on: 01 November 2007, 16:23:26 »
hi, can anyone on here do a lpg conversion for me? is it better to go somewhere and have it done or get a kit (if one is available) and DIY?? am seriously looking into it for my 3.0 elite.
any thoughts, cheers
any thoughts, cheers
15
Omega General Help / Re: V6 crank sensor location
« on: 28 October 2007, 10:44:01 »
You will find the little bugger right next to the oil filter, held in by one torx bolt (E8 i think)
and it plugs in at the rear of the plenum, where the wiring harness ends, just under the passenger side wiper arm. Take care when refitting to make sure wiring doesnt touch any hot bits!!
Hope this helps
and it plugs in at the rear of the plenum, where the wiring harness ends, just under the passenger side wiper arm. Take care when refitting to make sure wiring doesnt touch any hot bits!!
Hope this helps