1
Omega Electrical and Audio Help / Re: Battery discharged Fuse 7 circuit culprit
« on: 09 August 2010, 19:51:13 »Quote
Some change per model but Isn't fuse 7 windows?
- 19 September 2025, 03:44:00
- Welcome, Guest
News:
Please play nicely. No one wants to listen/read a keyboard warriors rants....
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Omega Electrical and Audio Help / Re: Headlamp recon
« on: 01 June 2010, 22:12:35 »
It may be worth mentioning that the Lens is not glass but Polycarbonate/Plastic-dont put any kind of solvent or anything scratchy near them!
Some have mentioned using Toothpaste!
eddie
Some have mentioned using Toothpaste!
eddie
3
Omega General Help / Re: rear bearing
« on: 19 April 2011, 22:36:54 »
Droning noises in the back can also be down to Inner Drive Shaft bearings on the Diff. Relatively easy to change.
eddie
eddie
4
Omega General Help / Re: 3.2 rear brake disc removal (or not)
« on: 04 April 2011, 03:11:04 »
Get underneath and slacken off the adjuster,you'll have to remove a heatshield first. The brake shoes tend to catch in a groove that has been worn into the drum part.
You can slacken off the one side at a time through the little hole in the drum/disc assembly. Trouble is knowing which direction to go! Its a right pain in the backend.
Far easier to slacken off as suggested,underneath where the cable splits in two,that way you are doing both sides at a time.
eddie
You can slacken off the one side at a time through the little hole in the drum/disc assembly. Trouble is knowing which direction to go! Its a right pain in the backend.
Far easier to slacken off as suggested,underneath where the cable splits in two,that way you are doing both sides at a time.
eddie
5
Omega General Help / Re: power steering help
« on: 10 October 2010, 23:30:18 »
Check your (front) tyre pressures,low pressure puts quite a load on the pump!
eddie
eddie
6
Omega General Help / Re: Coil Pack V6
« on: 01 September 2010, 21:38:29 »
A 1/4" socket set with a 'wobbly' connector will get at the 4 bolts holding it in. Then limber up your wrists and fingers!
eddie
eddie
7
Omega General Help / Re: steering all over the road
« on: 29 August 2010, 20:55:47 »
Check your front tracking,too much toe in can make the steering very lively!
Other than that,as per previous post.
eddie
Other than that,as per previous post.
eddie
8
Omega General Help / Re: Help Problem with Spark plugs
« on: 11 August 2010, 14:10:13 »
Dont forget copper grease when putting new ones in or you'll have an encore.
eddie
eddie
9
Omega General Help / Re: Crank case pressure build up?
« on: 03 August 2010, 13:32:01 »
Take the filler cap of and replace with a piece of Gauze held on with a cable tie ?
eddie
eddie
10
Omega General Help / Re: Omega B door moulding removal.......help!
« on: 18 May 2010, 23:57:18 »
If it is a rear door watch your positioning or it will catch the rear edge of the front door when opening.
eddie
eddie
11
Omega General Help / Re: Still revving up!! Arrrgghhhh!!!
« on: 23 April 2010, 21:19:47 »
EGR? Dont bother with the prize! 
eddie
eddie
12
Omega General Help / Re: Seized piston in rear brake caliper!
« on: 12 April 2010, 22:27:52 »
I had same problem on a front caliper. by removing the outer pad and dropping the caliper back over the disk I was able to pump the piston out a bit further. Plenty of silicon grease under the rubber boot on the piston surface and then used a Ford rotary retractor to squeeze and twist the piston back in.
I did this a couple of times to lubricate and free up the piston. HTH.
eddie
I did this a couple of times to lubricate and free up the piston. HTH.
eddie
13
Omega General Help / Re: Urgent help required please re handbrake adjuster!
« on: 09 March 2010, 21:23:37 »
Please be aware that which ever direction works for one side will be the opposite for the other side!
I 'think' it is up on drivers side and down on other side.
The so called toothed wheel you are working on actually has rounded cut outs as opposed to straight like a cog or gear wheel.
If you are trying to adjust Handbrake travel then you are working on the wrong adjusters! You should be under the car working on the handbrake adjuster which is just before where the cable divides to each side.
eddie
I 'think' it is up on drivers side and down on other side.
The so called toothed wheel you are working on actually has rounded cut outs as opposed to straight like a cog or gear wheel.
If you are trying to adjust Handbrake travel then you are working on the wrong adjusters! You should be under the car working on the handbrake adjuster which is just before where the cable divides to each side.
eddie
14
Omega General Help / Re: Removing throttle cable...
« on: 15 February 2010, 22:41:51 »
watch you dont break the plastic cruise connector like what I did!
Unable to replace same 'cause I still cant get the bloody throttle connector of. :-/
Wondering if a bit of gentle heat will expand it enough to come of?
eddie
Unable to replace same 'cause I still cant get the bloody throttle connector of. :-/
Wondering if a bit of gentle heat will expand it enough to come of?
eddie
15
Omega General Help / Re: Electric Seat Manual Winding Crank Tool
« on: 22 January 2010, 22:51:52 »
£2 ! That must be a record-any one beat that?
All I got was £1
eddie
All I got was £1
eddie