Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Omega Electrical and Audio Help / Re: Digital Radio

« on: 24 April 2008, 19:33:40 »

looked at this yesterday
very interested in getting one for mine
http://www.omegaowners.com/forum/YaBB.pl?num=1208800810

YES YES i have got to get one of those well spotted

2

Omega General Help / Re: engine management light on

« on: 01 July 2008, 19:58:50 »

mine went a bit like yours and ended up being the cam sharft sensor cost £25 for the part and rickyboy to explain how to do it which was pretty simple and bobs ur uncle and fannys ur aunt

3

Omega General Help / Re: engine management light on

« on: 01 July 2008, 19:54:30 »

rickyboy will help you out all the way he helped me out and my car now runs like a dream  

4

Omega General Help / Re: Need help with fault codes

« on: 11 June 2008, 21:40:51 »

the light either comes on straight away and starts cutting out at exactly 4500rpm or like earlier it did not come on at all untill i got home when after popping into my mates house started it and it came straight back on

5

Omega General Help / Re: Need help with fault codes

« on: 11 June 2008, 21:23:58 »

maybe i should have said this earlier but i booted it to work this morning in sport mode and it was after this that it happened

6

Omega General Help / Re: Need help with fault codes

« on: 11 June 2008, 21:14:12 »

it is gonna cost about 80 quid, just changed at an interval

7

Omega General Help / Re: Need help with fault codes

« on: 11 June 2008, 21:02:59 »

i did get the full kit fitted, do you think it is worth getting the camshaft sensor done anyway as i have booked it in for tomorrow

8

Omega General Help / Re: Need help with fault codes

« on: 11 June 2008, 20:58:38 »

would the tensioners come with the cam belt kit?

9

Omega General Help / Re: Need help with fault codes

« on: 11 June 2008, 20:49:03 »

no but it did come on for a few mins so the guy at the garage cleaned out the throttle body cause i was losing a bit of power and that seemed to sort it out and i have just been down to somerset with no probs

10

Omega General Help / Re: Need help with fault codes

« on: 11 June 2008, 20:42:57 »

yes about 2 months ago

11

Omega General Help / Need help with fault codes

« on: 11 June 2008, 20:35:49 »

I have just done a paper clip test and got the following code 10 then 3 then 4 then 10 again can anyone tell me what this means before i done the test the chap at the garage reckons i need a new crank shaft sensor do you think this is right. Thanks

12

Omega General Help / Re: HELP!!!!! Advice needed urgently

« on: 28 May 2008, 21:18:59 »

No fault codes is a good thing in most cases, unless the bulb is either blown or 'missing'!
Yes, older miggys do give fault codes and are easy enough to read without the 'help' of a garage.

Since you have no engine management light on, should just be what James and myself said, needs a good clean up!  

(yes, I realise what I've just done and yes sir, I'm an idiot!  )

The engine management light did come on for about 2 secs and went off again the garage said this was just where the revs dipped so low and it has not come on again

13

Omega General Help / Re: HELP!!!!! Advice needed urgently

« on: 28 May 2008, 20:39:28 »

All advice is good, thanks for your help

14

Omega General Help / Re: HELP!!!!! Advice needed urgently

« on: 28 May 2008, 20:37:46 »

No fault codes i might sound like a wally but do the older miggys come up with fault codes any way no is the answer.I am putting it into the garage tomorrow as i have not got a clue but i will write down what you have said and pass it on as i dont think they will do all you have said. Thanks for the advice

15

Omega General Help / HELP!!!!! Advice needed urgently

« on: 28 May 2008, 20:17:58 »

Whilst driving today my car lost a bit of power then came back it done this a couple of times then i noticed the revs kept dipping, but once i got to work it was fine,then on the way home it done the same thing. I popped into the garage i go to and he said the throttle block needed to come off and needed cleaning as a flap was not opening or shutting properly and said this is what is making the revs dip.      I want to know if this is right or if anyone has any other ideas i need to get this done as quick as i can as i am going to somerset on holiday this saturday with the family and dont want to let my sons down. PLEASE HELP