1
Omega General Help / Re: Cam belt change
« on: 21 June 2014, 19:16:12 »
Just contacted James..
- 17 September 2025, 09:03:04
- Welcome, Guest
News:
Welcome to OOF
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Omega General Help / Re: Cam belt change
« on: 21 June 2014, 19:06:31 »
Sorry for not replying as I have been busy....Anyone interested doing the job please contact by email....
3
Omega General Help / Cam belt change
« on: 18 June 2014, 15:40:30 »
Hi all, not been on here for a while due to work commitments and having second car.
My question is does anyone know who could do a cambelt change around the Romford Essex area as it is overdue by time but not mileage. (V6 2.5)
My question is does anyone know who could do a cambelt change around the Romford Essex area as it is overdue by time but not mileage. (V6 2.5)
4
Omega General Help / Re: Air con pressure switch override
« on: 21 April 2013, 22:09:49 »
Perhaps I did not make it clear. Clutch failed electrically last summer O/C coil. Plenty of gas in system so with eco off Rev =600 but no cold air as clutch was just free wheeling. Was thinking then to have the clutch replaced as someone suggested and could do the job but was never done. Then a leak must have developed and revs dropped to 500 as it should with low pressure in system. So over riding the pressure switch will not cease up aircon pump as it is permanently disengaged.
5
Omega General Help / Re: Air con pressure switch override
« on: 20 April 2013, 16:38:21 »
I have no preblem with temperature just wanted to know how to overide the switch that senses gas is too low in aircon system and bring up the revs to 600 again. Clutch of Compressor is fubared anyway and system is low on gas.
6
Omega General Help / Air con pressure switch override
« on: 19 April 2013, 15:33:33 »
As my aircon pump is NBG and will be replaced hopefully next month I would like to over ride the pressure switch to bring the revs up and make use of the aircon fans, Can this be done?
7
Omega General Help / Re: AC compressor clutch
« on: 08 August 2012, 21:30:13 »
Yes 12v present. Thanks for info. Will have a go.....crossed fingers
9
Omega General Help / AC compressor clutch
« on: 07 August 2012, 22:29:30 »
Just had a complete regas, vacuum the full works. we now found the clutch is not operating. 12v is present on plug from the relay. my question is can they be removed or does it mean a complete new compressor?
10
Omega General Help / HBV
« on: 30 May 2012, 13:48:22 »
Hi all, not been on for a while as not having problems. But yesterday.....coolant level low. water running down back of engine but no water can be seen from top end. But noticed today when heater set to high...bloody hot in the car (lol) the loss of water has stopped. HBV or hose or both?
Any advice welcome
Lou
Any advice welcome
Lou
11
Omega Electrical and Audio Help / Re: Heated seat
« on: 18 December 2011, 14:34:16 »
Thanks for advice...I will be careful..we dont want a hole in the seat or any where else for that matter.lol 
12
Omega Electrical and Audio Help / Re: help please battery change radio code cdr2005
« on: 18 December 2011, 14:31:49 »
Changed my battery recently, connected a small battery charger set to trickle charge, clipped small crock clips on terminals and removed- replaced battery without any problems and kept all codes. I can not think of any reasons why this method would cause a problem?
13
Omega Electrical and Audio Help / Heated seat
« on: 17 December 2011, 21:41:13 »
Recently I have notice that when I switch on my heater in my seat I almost get burned in some delicate places within a minute or so. Should this be controlled and if so anything that can be done to stop burning my ar....
14
Omega General Help / Re: Torque setting for centre bolt
« on: 08 October 2011, 15:36:36 »
Thanks for info...
15
Omega General Help / Torque setting for centre bolt
« on: 08 October 2011, 14:02:55 »
What is the required torque for the bolt on subframe centre bolt (Through the doughnut) and is it torqued with the wheels down?