Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Omega General Help / Re: Con rod bearings

« on: 10 October 2010, 18:02:57 »

Hi fella, crank is not scored or marked will have to chech con rod face but i will check with the micrometer anyway, any ideas on how much a big end bearings is?

2

Omega General Help / Con rod bearings

« on: 10 October 2010, 11:52:26 »

Well after stripping down my engine i discovered the loud knocking was a con rod bearing run out probs due to no oil so i can

1) put a whole set of bearings on it,
2)just put one bearing on it
3)scrap it and just get a second hand bottom end.

your thoughts?

3

Omega General Help / Re: Plumbing the beast

« on: 26 May 2010, 00:44:19 »

just a thought have you tried running it with the fuel cap off?

4

Omega General Help / Re: N.Ireland Omegas

« on: 17 July 2010, 12:59:18 »

This James?  Hi fella

I got it on running the cams in atm few things to fix, check and tidy up. but could do with having you put it on the computer to check as eml is on. prob with immobliseras well i think but im just gona put a switch on it for the time being as a live to the starter gets it going.

re: boot spoiler i promised it to my mate ages ago so i will check if he still want it or not. If not then you can take it ns.

5

Omega General Help / Re: N.Ireland Omegas

« on: 14 July 2010, 23:13:34 »

oh and by pure concidince i have a boot spoiler here too.

6

Omega General Help / Re: N.Ireland Omegas

« on: 14 July 2010, 23:12:29 »

could u come and put a timing belt on for me it an mv6 having a spot of bother,

7

Omega General Help / Re: water pipes

« on: 17 July 2010, 00:53:40 »

top job fella,thank-you

im just gonna see if it will start now 

8

Omega General Help / water pipes

« on: 16 July 2010, 20:29:15 »

ok just finishing getting it rebuilt, x30xe engine

questions are about the water pipes,

the one from the stainless pipe at the back of the block goes to?

the one from the bridge in the head (were water temp sensor is) goes to?

9

Omega General Help / Re: Whats this?

« on: 13 July 2010, 09:20:47 »

illl check part num this clould be a pointless post tbh.

10

Omega General Help / Re: Whats this?

« on: 13 July 2010, 09:20:40 »

illl check part num this clould be a pointless post tbh.

11

Omega General Help / Re: Whats this?

« on: 13 July 2010, 00:16:43 »

i duno,

just changed omega engine and found this, mite be important.

i'm a dumb fucjer somethimes.

12

Omega General Help / Whats this?

« on: 12 July 2010, 23:39:14 »

13

Omega General Help / Re: Trouble getting timing belt on.

« on: 07 July 2010, 16:36:00 »

i have tried it by the book its a flanged bottom tensioner so i have put it on anti clockwise still a mile out. clockwise is the same wont strech to get on 4th cam wheel,

closest i have got is putting it on everything except the top tensioner(not spring one), ajusted the cam wheels independently to take up the slack while still keeping them in alignment and trying to push the top tensioner down even then i still need bout an eighth of an inch more belt?

14

Omega General Help / Re: Trouble getting timing belt on.

« on: 07 July 2010, 16:07:41 »

Hi bro

no dvd but have sykes pickavant kit and have all tensioners ajusted so that i have max slack unless the one with the allen hole has a trick to it?

15

Omega General Help / Trouble getting timing belt on.

« on: 07 July 2010, 13:46:21 »

Im having trouble getting my timing belt on it seems about an eighth too short,  all belts are 225 teeth long i have the smaller idlers too (56mm)

The heads are off a block with the lower tensioner higher up the block than the new block which has the tensioner right beside the crank pulley.

any ideas?