Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: 1 [2]  All   Go Down

Author Topic: Plastic Metal Part 2  (Read 1546 times)

0 Members and 1 Guest are viewing this topic.

Elite Pete

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chester
  • Posts: 19580
  • My spider senses are tingling
    • Audi SQ5 GSX1400
    • View Profile
Re: Plastic Metal Part 2
« Reply #15 on: 09 October 2008, 21:37:04 »
Quote
Quote
Quote
so could you pete if you buy my TRACTOR ;D ;D ;D ;D
If I get the job ive just applied for I might take you up on the offer ;)

Vidal Sassoon?????
He couldn't afford me ;)
Logged
Retired

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 34029
  • Git!
    • View Profile
Re: Plastic Metal Part 2
« Reply #16 on: 09 October 2008, 22:14:38 »
What the rather hell was he using silicon on.....

In the preseence of oil etc it turns into gorilla snot!
Logged

JueV6

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Kent
  • Posts: 1464
    • View Profile
Re: Plastic Metal Part 2
« Reply #17 on: 09 October 2008, 23:11:58 »
Not sure WHO built the 1st one, but....... even the MV had vast amouts of silicon arounf the rear main cap and sump bolt holes
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 34029
  • Git!
    • View Profile
Re: Plastic Metal Part 2
« Reply #18 on: 10 October 2008, 08:10:44 »
Quote
Not sure WHO built the 1st one, but....... even the MV had vast amouts of silicon arounf the rear main cap and sump bolt holes


Well in which case hes been buggering about......silicon!!! :( >:(.

Christ, if silicon would do the job we wouldn;t all be paying considerably more for fancy sealents in smaler quantities.

Hes breaked that himself!
Logged

JueV6

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Kent
  • Posts: 1464
    • View Profile
Re: Plastic Metal Part 2
« Reply #19 on: 10 October 2008, 08:32:10 »
lol keeps me busy.
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 34029
  • Git!
    • View Profile
Re: Plastic Metal Part 2
« Reply #20 on: 10 October 2008, 08:37:24 »
Given that he would have to swap the sump to fit the lump in the vectra, I bet hes used some of the BandQ value silicon to seal it!

I would warn him that he needs the specialist Vx stuff for the next one! (the grey cartridge tube type as used for the oil cooler!)
« Last Edit: 10 October 2008, 08:38:52 by Mark »
Logged

JueV6

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Kent
  • Posts: 1464
    • View Profile
Re: Plastic Metal Part 2
« Reply #21 on: 10 October 2008, 10:08:13 »
This time it was rebuilt by an EX-Vx workshop supervisor, if that makes any difference ;D ;D ;D

I must admit tho, I saw it yesterday and ..It is a very tidy looking Install.
 ;D ;D
« Last Edit: 10 October 2008, 10:09:21 by Juedu2 »
Logged
Pages: 1 [2]  All   Go Up
« previous next »
 

Page created in 0.045 seconds with 17 queries.