Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1]   Go Down

Author Topic: How do I unplug CL door motor?  (Read 1231 times)

0 Members and 1 Guest are viewing this topic.

terry paget

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Midsomer Norton Somerset
  • Posts: 4633
    • 3 Astras 2 Vectra
    • View Profile
How do I unplug CL door motor?
« on: 03 September 2013, 20:47:14 »
Is there a trick to unplugging central locking motors? It was easy before they put in door air bags. Now I try to grasp the connector locking levers, but I cannot get a thumb behind the inside lever because the air bag is in the way
Logged

tunnie

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Surrey
  • Posts: 37526
    • Zafira Tourer & BMW 435i
    • View Profile
Re: How do I unplug CL door motor?
« Reply #1 on: 03 September 2013, 20:50:12 »
Easy enough as I recall for my guide:

http://www.omegaowners.com/forum/index.php?topic=90543.0

Also there are no airbags in the doors? Only a sensor.
Logged

terry paget

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Midsomer Norton Somerset
  • Posts: 4633
    • 3 Astras 2 Vectra
    • View Profile
Re: How do I unplug CL door motor?
« Reply #2 on: 03 September 2013, 21:17:57 »
Quote from: tunnie on 03 September 2013, 20:50:12
Easy enough as I recall for my guide:

http://www.omegaowners.com/forum/index.php?topic=90543.0

Also there are no airbags in the doors? Only a sensor.
Thanks. Still struggling. Do I squeeze the levers together, or merely unclip (lift up?) as your guide says. I cannot see what I am doing.
Logged

amba

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Medway towns
  • Posts: 4825
    • View Profile
Re: How do I unplug CL door motor?
« Reply #3 on: 03 September 2013, 21:28:49 »
If you have removed all the metal rods and the main door latch as per the guide you should be able to move the solenoid into a postion that allows you to see the plug end.

Did mine last week but cant remember how it pulls apart,think plastic "tang" needs lifting slightly to fully release,but cant be totally sure.

I found the guide perfect to follow :y
Logged

tunnie

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Surrey
  • Posts: 37526
    • Zafira Tourer & BMW 435i
    • View Profile
Re: How do I unplug CL door motor?
« Reply #4 on: 03 September 2013, 21:48:05 »
Push them together and pull down as far as I remember  :y
Logged

robson

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Nr Ashford Kent
  • Posts: 1828
    • 2.6 facelift 2003
    • View Profile
Re: How do I unplug CL door motor?
« Reply #5 on: 04 September 2013, 11:33:26 »
When I did mine I had the same problem until I released the electric cables which were clipped to the base of the door opening with these unclipped the motor will come  up high enough to see clamps on plug in connector.
Logged

terry paget

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Midsomer Norton Somerset
  • Posts: 4633
    • 3 Astras 2 Vectra
    • View Profile
Re: How do I unplug CL door motor?
« Reply #6 on: 04 September 2013, 15:22:03 »
Thanks to all. I have got it off now. I got off the LH door motor by cutting the cable (car is to be scrapped), when I could see that I had been basically right - I had to press the two levers together and push the cable down away from the motor. I removed the RH motor without cutting anything, I simply disconnected the levers from the door lock, undid the lower two lock screws and loosened the top screw, then I could rotate the motor lock assembly away from the airbag and release the connector.

Are you sure it is is not an airbag, Tunnie? It is black, full door width and 4" deep, made by Siemens and labelled ACHTUNG SIETENAIRBAG and CAUTION SIDE AIRBAG.
Logged

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39524
    • ML350 TDM SmartRoadster
    • View Profile
Re: How do I unplug CL door motor?
« Reply #7 on: 04 September 2013, 16:44:57 »
Quote from: terry paget on 04 September 2013, 15:22:03
...
Are you sure it is is not an airbag, Tunnie? It is black, full door width and 4" deep, made by Siemens and labelled ACHTUNG SIETENAIRBAG and CAUTION SIDE AIRBAG.

It'd be a very small airbag Terry .......  ;)  ;) It's a sensor to tell the airbag to go off
Logged

robson

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Nr Ashford Kent
  • Posts: 1828
    • 2.6 facelift 2003
    • View Profile
Re: How do I unplug CL door motor?
« Reply #8 on: 04 September 2013, 17:50:06 »
The sensor is quite small isnt it mine was Blue
Logged

terry paget

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Midsomer Norton Somerset
  • Posts: 4633
    • 3 Astras 2 Vectra
    • View Profile
Re: How do I unplug CL door motor?
« Reply #9 on: 04 September 2013, 20:14:53 »
You are all quite right. I felt behind the steel plate labelled air bag and there is nothing there. It's just a steel plate. At the rear end there is a sensor. Both are in the way of my disconnecting the the loom from the door motor.   
Logged

tunnie

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Surrey
  • Posts: 37526
    • Zafira Tourer & BMW 435i
    • View Profile
Re: How do I unplug CL door motor?
« Reply #10 on: 04 September 2013, 21:51:11 »
Had that sensor out a few times, to replace Window motors & window glass. It's riveted in, so has to be drilled out. Taken it out and there is nothing to it  :y
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.034 seconds with 22 queries.