Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please play nicely.  No one wants to listen/read a keyboard warriors rants....

Pages: [1]   Go Down

Author Topic: Tin worm!  (Read 1209 times)

0 Members and 1 Guest are viewing this topic.

Shackeng

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Ramsbury
  • Posts: 7763
    • 3.2 Elite 2.0 TitX Mondeo
    • View Profile
Tin worm!
« on: 02 February 2014, 20:21:16 »



While sorting out some rusty brake pipes, I found this hiding under the body seal in the NS inner rear wing! It will, I think, require a plate welding in, as it is almost through to the inside. Is this a common rust area?
Logged

lee4206

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • southampton
  • Posts: 679
  • Mot Tester
    • 2000 3.0l manual MV6
    • View Profile
Re: Tin worm!
« Reply #1 on: 02 February 2014, 21:45:59 »

I Had to repair mine in the same place  but mine was a lot worse  and my old one was the same .  I'd say it was a common area to go.   Check under the cover at the end of the sill too!
Logged
VAUXHALL TRADE CLUB AND HALFORDS TRADE CARD  AND V6 LOCKING KIT HOLDER  always happy to help if poss

cd 2.2

  • Guest
Re: Tin worm!
« Reply #2 on: 02 February 2014, 22:19:59 »

Yep under the rear sill cover is very common, both mine and my dad's are going there and I believe linked to that very same issue??
Logged

Shackeng

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Ramsbury
  • Posts: 7763
    • 3.2 Elite 2.0 TitX Mondeo
    • View Profile
Re: Tin worm!
« Reply #3 on: 03 February 2014, 16:39:26 »

Is this an MOT failure?
Logged

Shackeng

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Ramsbury
  • Posts: 7763
    • 3.2 Elite 2.0 TitX Mondeo
    • View Profile
Re: Tin worm!
« Reply #4 on: 03 February 2014, 19:14:44 »

Is this an MOT failure?

Any experts on MOT's here?
Logged

lee4206

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • southampton
  • Posts: 679
  • Mot Tester
    • 2000 3.0l manual MV6
    • View Profile
Re: Tin worm!
« Reply #5 on: 03 February 2014, 21:11:23 »

From the pic I would say yes as its within 30cm of the spring mount.  When you clean it I can almost guarantee it will go through. 
Also remove the side bolster and check the floor by the seat belt mount as it spreads a lot further than it looks..
Logged
VAUXHALL TRADE CLUB AND HALFORDS TRADE CARD  AND V6 LOCKING KIT HOLDER  always happy to help if poss

b4ndit

  • Guest
Re: Tin worm!
« Reply #6 on: 03 February 2014, 21:18:13 »

can confirm what Lee4206 says  would fail an mot
Logged

Shackeng

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Ramsbury
  • Posts: 7763
    • 3.2 Elite 2.0 TitX Mondeo
    • View Profile
Re: Tin worm!
« Reply #7 on: 03 February 2014, 22:10:00 »

Thanks very much guys, I'll get it fixed. :y :y :y
Logged
Pages: [1]   Go Up
 

Page created in 0.009 seconds with 17 queries.