Where is the OBD2 socket on a 2004 Astra 1.6 petrol?

Started by terry paget, 03 November 2018, 15:55:18

Previous topic - Next topic

0 Members and 0 Guests are viewing this topic.

terry paget

Here is sample of the oil I drained out. This was poured out of the oil change collector so was on the top. after settling for 24 hours.


dave the builder

but what was the strainer pick up  like  :-\
most of the sludge will be in the sump now
worth cleaning out and trying with fresh oil 10w40 ;)

terry paget

I am trying to drop the sump. I have removed all the bolts and screws I can see attaching the sump to the block and the bell housing, but it did not fall off. I hve given it tentative taps with a hammer, but it stays put. Is there a trick to release it?

Doctor Gollum

Onanists always think outside the box.

aaronjb

Probably glued on with instant gasket - it was a nightmare to get sumps off the 1ZZFE in the MR2, usually needing a chisel or wide scraper and a lump hammer!

Nick W

Quote from: terry paget on 16 November 2018, 17:29:43
I am trying to drop the sump. I have removed all the bolts and screws I can see attaching the sump to the block and the bell housing, but it did not fall off. I hve given it tentative taps with a hammer, but it stays put. Is there a trick to release it?


scrape part of the gasket out with a Stanley knife, then pry the sump off with a nylon wedge in the hole.
You could knock a screwdriver into the gasket and pry the sump off that way. But you'll probably have to straighten and or dress the edges afterwards.

Kevin Wood

Quote from: Nick W on 16 November 2018, 17:40:20
Quote from: terry paget on 16 November 2018, 17:29:43
I am trying to drop the sump. I have removed all the bolts and screws I can see attaching the sump to the block and the bell housing, but it did not fall off. I hve given it tentative taps with a hammer, but it stays put. Is there a trick to release it?


scrape part of the gasket out with a Stanley knife, then pry the sump off with a nylon wedge in the hole.
You could knock a screwdriver into the gasket and pry the sump off that way. But you'll probably have to straighten and or dress the edges afterwards.

.. and re-bore it, replace the main and big end bearings... ;)
Tech2 services currently available. See TheBoy's price list: http://theboy.omegaowners.com/

dave the builder

look at pics of the sump on ebay or google to see where all the bolt holes are  :y

terry paget

'Drop the sump' sounds trivial, but it's not. Even removing the front exhaust took a while, and involved blowtorch and angle grinder. I believe I have now removed all the sump retaining screws and bolts, but the sump has not fallen off. I am only doing this to inspect the oil pickup strainer, the car is scrap.

I shall pause at this point. I need the garage for other jobs. Jonny is here this weekend, I must remove the rear wheels froim his Astra.

Here are all the screws and bolts I removed.
[img]

terry paget


dave the builder

not enough small bolts out yet  :y 15 holes i count  ,not including what goes into gearbox bell housing

Webby the Bear

Yes there are some that go through the bell housing. When u see them you'll know
RIP Paul Lovejoy

terry paget

I will look again. I may have dropped some screws.

terry paget

Thanks Dave. I have found 2 more screws, left hand end, in tunnels, removed them, tapped sump with hammer and off it fell.


Looks like I was using tar as a lubricant.

terry paget

Here is the sump. I presume the soft bit on top is the strainer.