Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: 1 [2]  All   Go Down

Author Topic: Where to Locate Axle Stands (Rear)  (Read 10441 times)

0 Members and 1 Guest are viewing this topic.

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 30816
  • If you can't eat them, join them...
    • Feetses.
Re: Where to Locate Axle Stands (Rear)
« Reply #15 on: 08 May 2019, 20:00:20 »
Quote from: Doctor Gollum on 08 May 2019, 08:42:28
3. I used a torque wrench ::)

Actual setting is 320 NM :y

My torque wrench only goes to 300, so did it up with that plus a BFT smidge with a bar :y
I will correct that after work... That torque is for the front :-[
Logged
Onanists always think outside the box.

Enceladus

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • London
  • Posts: 1108
Re: Where to Locate Axle Stands (Rear)
« Reply #16 on: 08 May 2019, 23:01:49 »
Quote from: polilara on 08 May 2019, 19:19:32
OK, 320Nm when it is time for that.
Rear hub bearings are 300Nm.
It's the front hub bearings that are 320Nm.
Not that it makes much difference, but it does help to have the target understood and correct.
Logged

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1126
    • 2.6 Y26SE Elegance 2001
Re: Where to Locate Axle Stands (Rear)
« Reply #17 on: 09 May 2019, 04:05:11 »
OK, thanks correction, no problem yet, have to remove it first. Is there any typical life time for rear bearing of Omega?
Logged

mandula

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 174
    • Opel Omega -03, Z22XE man
Re: Where to Locate Axle Stands (Rear)
« Reply #18 on: 09 May 2019, 07:54:06 »
Quote from: polilara on 09 May 2019, 04:05:11
OK, thanks correction, no problem yet, have to remove it first. Is there any typical life time for rear bearing of Omega?

I don't know is it typical, but my originals lasted about 200 000 km and 220 000 km (or at least I could not find any markings that they have been replaced earlier).
Then one re-newed needed to be replaced after 100 000 km. Now I'm waiting was it just bad batch or is the other one also going soon..
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 30816
  • If you can't eat them, join them...
    • Feetses.
Re: Where to Locate Axle Stands (Rear)
« Reply #19 on: 09 May 2019, 10:04:36 »
My plod was on its original ones at 285k miles, so nearly 500k kms :o

Some people seem to kill them in a third of that :-\
Logged
Onanists always think outside the box.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1126
    • 2.6 Y26SE Elegance 2001
Re: Where to Locate Axle Stands (Rear)
« Reply #20 on: 09 May 2019, 11:31:53 »
Interesting difference, perhaps winter time here in Finland has something to do with it. How well the lubrication works in -20C. However, I still think that my noise is bearing failure. It is not rattling but "croaking". The sound did not change when braking with foot or handbrake so not dragging pads or shoes. 
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 30816
  • If you can't eat them, join them...
    • Feetses.
Re: Where to Locate Axle Stands (Rear)
« Reply #21 on: 09 May 2019, 12:10:20 »
Did the sound change during left/right cornering?
Logged
Onanists always think outside the box.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1126
    • 2.6 Y26SE Elegance 2001
Re: Where to Locate Axle Stands (Rear)
« Reply #22 on: 09 May 2019, 12:25:24 »
Yes, remember when turning left sound was increasing (in right side). Also it was stronger in certain speed e.g. 40-50 km/t. Could not hear. it as clearly in higher speeds when othe noises increased, too.
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 30816
  • If you can't eat them, join them...
    • Feetses.
Re: Where to Locate Axle Stands (Rear)
« Reply #23 on: 09 May 2019, 13:46:03 »
Does indeed sound like a bearing :y
Logged
Onanists always think outside the box.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1126
    • 2.6 Y26SE Elegance 2001
Re: Where to Locate Axle Stands (Rear)
« Reply #24 on: 09 May 2019, 14:50:31 »
Yes, like a worn bearing.
Logged

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1126
    • 2.6 Y26SE Elegance 2001
Re: Where to Locate Axle Stands (Rear)
« Reply #25 on: 09 May 2019, 16:09:36 »
Actually the hub nut was 32mm... Sedan 2001
Logged
Pages: 1 [2]  All   Go Up
« previous next »
 

Page created in 0.015 seconds with 16 queries.