Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[JamesV6CDX]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

[Richie London]

try   http://www.tooled-up.com/Product.asp?PID=15628

[Mr Skrunts]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

Whats that in old money then?  Ft Lb's?

[Richie London]

i bought this off this site a few months ago for work. saves so much time marking everything out now
http://www.tooled-up.com/Product.asp?PID=123904

[Bandit127]

Sykes Pickavant do a good one.
http://www.shacktools.com/sykespickavant-12-torque-wrench-330nm-p-5572.html?manufacturers_id=14&osCsid=ec4d48a89da5be4d9f03a6d91b48974c

I have a 600Nm one for work (not the same make) with a 3/4 drive. It has a 3/4 to 1/2 reducer rated at 500Nm. Expensive - but a whole load easier than pulling full torque on a cheaper wrench that is at full capacity...  You wouldn't want to carry it on a train though  

[Elite Pete]

Close enough
http://www.halfords.com/webapp/wcs/stores/servlet/product_storeId_10001_catalogId_10151_productId_178621_langId_-1_categoryId_165469

[Bandit127]

Close enough
http://www.halfords.com/webapp/wcs/stores/servlet/product_storeId_10001_catalogId_10151_productId_178621_langId_-1_categoryId_165469

As post above Pete. I woudn't want to pull more than 200 on one of those if my living depended on it. In fact, I do pull exactly 200 on one of those. Day in, day out.

Luckily, I work for a big company so if I injure myself I still get paid.

If I needed to do more than that, I would use the big one.

[TheBoy]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

For wheel bearings, a fart and 2 grunts does the trick!

[cem_devecioglu]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

For wheel bearings, a fart and 2 grunts does the trick!

 

[Andy B]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

For wheel bearings, a fart and 2 grunts does the trick!

I think you'll find it's a fart & then another quarter turn!      

[Kevin Wood]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

For wheel bearings, a fart and 2 grunts does the trick!

.. or a precisely measured 15 stone applied a precisely measured distance along the breaker bar.

Kevin

[TheBoy]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

For wheel bearings, a fart and 2 grunts does the trick!

.. or a precisely measured 15 stone applied a precisely measured distance along the breaker bar.

Kevin

Thats JamesV6CDX knackered then.  Perhaps if he, Maria, and hannah all get on it together it might be close

[Kevin Wood]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

For wheel bearings, a fart and 2 grunts does the trick!

.. or a precisely measured 15 stone applied a precisely measured distance along the breaker bar.

Kevin

Thats JamesV6CDX knackered then.  Perhaps if he, Maria, and hannah all get on it together it might be close

He's just going to need a longer breaker bar. Or a bigger beer gut.

Kevin

[JamesV6CDX]

I take it the wheelbearing torque doesn't need to be that specific then, as long as it's effing tight?

[Richie London]

A Torquewrench capable of 320nm, with a 1/2 drive? Any ideas?

For wheel bearings, a fart and 2 grunts does the trick!

I think you'll find it's a fart & then another quarter turn!      

be careful not to push too hard as you could follow through