Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: [1]   Go Down

Author Topic: 3.2 exhaust manifolds  (Read 1537 times)

0 Members and 1 Guest are viewing this topic.

djhorner

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • isle of lewis
  • Posts: 73
    • omega mv6
    • View Profile
3.2 exhaust manifolds
« on: 18 March 2013, 19:19:37 »
i'm looking for manifolds to put on my 3..0
Logged

twiglet

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Norwich, Norfolk
  • Posts: 2171
  • 2008 BMW E61 535D LCi M Sport
    • View Profile
Re: 3.2 exhaust manifolds
« Reply #1 on: 18 March 2013, 20:59:44 »
PM sent.  :y
Logged
It doesn't matter how far you push the envelope, it will always be stationery...

HockeyDave55

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Milton Keynes
  • Posts: 597
    • 2000my 3.0 police special
    • View Profile
Re: 3.2 exhaust manifolds
« Reply #2 on: 19 March 2013, 18:24:09 »
On this subject, when we change the over, are we gonna have problems with the nuts to the heads???
Logged

djhorner

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • isle of lewis
  • Posts: 73
    • omega mv6
    • View Profile
Re: 3.2 exhaust manifolds
« Reply #3 on: 23 March 2013, 16:34:37 »
not as far as i'm aware just need to cut 5mm off down pipe there is a link showing how to do it
Logged

sjc

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Alloa, Scotland
  • Posts: 727
    • Ultra-dull Audi TDi
    • View Profile
Re: 3.2 exhaust manifolds
« Reply #4 on: 24 March 2013, 08:02:07 »
Logged
If you Elite an MV6, does that make it an MVee-leet?

MV6Danny

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Swindon, Wiltshire
  • Posts: 491
  • Driving at the speed of light
    • 99 irmscher mv6 3l Manual
    • View Profile
Re: 3.2 exhaust manifolds
« Reply #5 on: 27 March 2013, 03:55:44 »
Only need to cut the down pipes down by a bit as already stated. Need to use 3.2 manifold gaskets aswell as the 3.0 have holes in them that you wont need. Also will need 2 3.0 downpipe to manifold gaskets on each downpipe for it to seal properly. Did mine last year when I changef head gaskets and all is still ok. No probs with the bolys in the heads not lining up with holes on msnifold. Good luck with it. :y
Logged
Back in the MV6 again now

MV6Danny

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Swindon, Wiltshire
  • Posts: 491
  • Driving at the speed of light
    • 99 irmscher mv6 3l Manual
    • View Profile
Re: 3.2 exhaust manifolds
« Reply #6 on: 27 March 2013, 04:08:12 »
Sorry for the bad typing. This is the lip you need to grind down. :y
Logged
Back in the MV6 again now

MV6Danny

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Swindon, Wiltshire
  • Posts: 491
  • Driving at the speed of light
    • 99 irmscher mv6 3l Manual
    • View Profile
Re: 3.2 exhaust manifolds
« Reply #7 on: 27 March 2013, 04:10:22 »
Needs to be ground down so 2 gaskets just sit over the top. Dont need a lot left on it. Hth
Logged
Back in the MV6 again now
Pages: [1]   Go Up
« previous next »
 

Page created in 0.043 seconds with 21 queries.