Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: Steve B on 22 April 2016, 13:32:06
-
Thanks to a nice old lady >:( >:( I need to swap the n/s wing...
Take it that its all bolt on... apart from the bolts along the top,where abouts are the others.. :y
-
There are 2 X 10mm hex screws at the bottom of the wing - you'll need to remove sill cover..... and any attachment to the wheelarch liner of course.
-
:)
(http://www.emgauge70s.co.uk/omega_cdx258.jpg)
-
Colour? :)
-
Colour? :)
Looks Metallic Pink to me :-*
-
Cheers Tick Tock :y Z594
Tis this colour http://www.ebay.co.uk/itm/331824001189?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
-
There are 2 X 10mm hex screws at the bottom of the wing - you'll need to remove sill cover..... and any attachment to the wheelarch liner of course.
;D keep going...
At least two more on the back edge... top one done from the door side, not as easy as it sounds...
Second one is about halfway down back edge... remove arch liner, then sound deadening foam and you can get to it.
Headlight and trim piece off, front bumper also off (at very least undone and pulled out/down on that side) as there's another 3 or 4 screws there ;)
-
There are 2 X 10mm hex screws at the bottom of the wing - you'll need to remove sill cover..... and any attachment to the wheelarch liner of course.
;D keep going...
At least two more on the back edge... top one done from the door side, not as easy as it sounds...
Second one is about halfway down back edge... remove arch liner, then sound deadening foam and you can get to it.
Headlight and trim piece off, front bumper also off (at very least undone and pulled out/down on that side) as there's another 3 or 4 screws there ;)
What can possibly go wrong :D
-
i thought that too.... think answer is sill clips and headlight fittings :-\
-
i thought that too.... think answer is sill clips and headlight fittings :-\
Headlight is three bolts, lower one is visible/accessible either from underneath or with a long 1/4" extension once the trim is off.
Sill is a piece of piss... one torx screw under the front corner and seven or so pop caps along the bottom edge... Then, with the wheel on full left lock for nearside (opposite for offside), simply tap the sill cover forward an inch or so and it simply falls off :y
What you find underneath it once removed is a whole different conversation ;D
-
(http://www.deutschnine.com/rennlist/porsche-944-sill-rot/944-sill-rot-02.jpg)
;D
-
i thought that too.... think answer is sill clips and headlight fittings :-\
Headlight is three bolts, lower one is visible/accessible either from underneath or with a long 1/4" extension once the trim is off.
Sill is a piece of piss... one torx screw under the front corner and seven or so pop caps along the bottom edge... Then, with the wheel on full left lock for nearside (opposite for offside), simply tap the sill cover forward an inch or so and it simply falls off :y
What you find underneath it once removed is a whole different conversation ;D
It will look brand new :y cheers for the howto Al :y
-
There are 2 X 10mm hex screws at the bottom of the wing - you'll need to remove sill cover..... and any attachment to the wheelarch liner of course.
;D keep going...
At least two more on the back edge... top one done from the door side, not as easy as it sounds...
Second one is about halfway down back edge... remove arch liner, then sound deadening foam and you can get to it.
Headlight and trim piece off, front bumper also off (at very least undone and pulled out/down on that side) as there's another 3 or 4 screws there ;)
Think i will take the bumper completely off owing to the fact that ive just gone and trashed the other front wing on a "No Exit" sign in a tesco car park. ::)
-
There are 2 X 10mm hex screws at the bottom of the wing - you'll need to remove sill cover..... and any attachment to the wheelarch liner of course.
;D keep going...
At least two more on the back edge... top one done from the door side, not as easy as it sounds...
Second one is about halfway down back edge... remove arch liner, then sound deadening foam and you can get to it.
Headlight and trim piece off, front bumper also off (at very least undone and pulled out/down on that side) as there's another 3 or 4 screws there ;)
Think i will take the bumper completely off owing to the fact that ive just gone and trashed the other front wing on a "No Exit" sign in a tesco car park. ::)
Like bumper cars up in Leicester land :o
-
Went up to nigel today and got a pair of front wings off him... Great condition..And he is stripping another one on his drive the same colour ready for the next time ;D ;D ;D Pm you mr EMD :y
-
Still not made a start on this yet ::) two questions.... 1,Do i need wheels off to remove arch liners ? And i see there held on by the odd platic nut and the push the pin through plastic studs... 2,Will i lose the plastic pins when i push them in ?
-
Still not made a start on this yet ::) two questions.... 1,Do i need wheels off to remove arch liners ? And i see there held on by the odd platic nut and the push the pin through plastic studs... 2,Will i lose the plastic pins when i push them in ?
Yes and almost certainly.
-
Still not made a start on this yet ::) two questions.... 1,Do i need wheels off to remove arch liners ? And i see there held on by the odd platic nut and the push the pin through plastic studs... 2,Will i lose the plastic pins when i push them in ?
Yes and almost certainly.
Any idea which one,s Shackeng ?
http://stores.ebay.co.uk/227s-Parts/Clips-to-fit-a-8mm-hole-/_i.html?_fsub=1296887013
-
Sadly I can't help there. RobG will know. :y
-
Still not made a start on this yet ::) two questions.... 1,Do i need wheels off to remove arch liners ? And i see there held on by the odd platic nut and the push the pin through plastic studs... 2,Will i lose the plastic pins when i push them in ?
Should be able to recover them once liner is removed
-
Still not made a start on this yet ::) two questions.... 1,Do i need wheels off to remove arch liners ? And i see there held on by the odd platic nut and the push the pin through plastic studs... 2,Will i lose the plastic pins when i push them in ?
Should be able to recover them once liner is removed
Thanks Rob :y
-
Job done, two wings fitted and all back together.....One question.....Whats that black canister thing that i had to move to get at one of the bolts behind the drivers wing with the pipes sticking out :-\
-
Job done, two wings fitted and all back together.....One question.....Whats that black canister thing that i had to move to get at one of the bolts behind the drivers wing with the pipes sticking out :-\
Charcoal infused canister for purge valve