1
Omega General Help / Re: Speedo
« on: 03 August 2011, 21:11:54 »
ok: but still need to know how to remove old unit 
- 15 June 2025, 17:56:18
- Welcome, Guest
News:
Please check the Forum Guidelines at the top of the Newbie section
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Omega General Help / Speedo
« on: 03 August 2011, 21:04:40 »
speedo on blink now stopped how to remove and refit local scrapyard have one but 140k on it mine has 97k do I inform dvla thanks once again 
3
Omega General Help / Re: Power Sterring oil spec
« on: 06 July 2011, 20:04:23 »
Thanks will do keep up the good work 
4
Omega General Help / Power Sterring oil spec
« on: 05 July 2011, 20:31:41 »
which oil to use and how to change it 92k best car ever owned thank 
6
Omega General Help / EGR
« on: 11 June 2011, 14:05:36 »
Please, 4 ? 99 2lt where is the erg
what is the cost of new
can i blank it off
will it matter :-?
what is the cost of new
can i blank it off
will it matter :-?
7
Omega General Help / egr valve?
« on: 21 April 2011, 07:05:56 »
please what noise dose egr valve make when it start to stick
I have what I thought was a exhast manifold leak, but no leaks when up on ram,sounds like a penny in a can but not
allways :-/
I have what I thought was a exhast manifold leak, but no leaks when up on ram,sounds like a penny in a can but not
allways :-/
8
Omega General Help / Re: rpm
« on: 19 March 2011, 17:45:44 »
ye butterfly is fully closed what next thanks :-/
9
Omega General Help / rpm
« on: 19 March 2011, 16:22:41 »
please what rpm should a 2lt 16v auto tick over at
mine is 900rpm seem a little fast no more ajustment on butterfly thanks
mine is 900rpm seem a little fast no more ajustment on butterfly thanks
10
Omega General Help / Re: Down pipe misthread
« on: 16 March 2011, 14:30:10 »
sorry i should have said on mine the stud had sheared :-?
11
Omega General Help / Re: Down pipe misthread
« on: 15 March 2011, 20:46:42 »
take manifold off drill out old stud retap put a set stud in from top of manifold i did this with three studs on mine do not use gasket seal or bodge it will only come out
13
Omega General Help / ATF Filter
« on: 15 March 2011, 19:08:50 »
please will the auto trans in my car be a25 or a35 as I am going to change atf and filter will get it from jpat 83k now runs like a dream thanks to all at OOF, get 38mpg doing 2k a mth mostley motorway mileage
14
Omega General Help / Dash Lights
« on: 05 February 2011, 11:29:18 »
Hi all just passed MOT 80k no probs, thanks to all from OOF.
Next step how to change bulbs behind fuel gauge,thanks
Next step how to change bulbs behind fuel gauge,thanks
15
Omega General Help / Re: Heater only working on hottest?
« on: 22 January 2011, 17:04:35 »
Hi just in front of nearside wheel on bott of bumper 14mm hole,but check 2 wires running back to harness,1 of mine had broke only thin wire