Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: [1]   Go Down

Author Topic: Having trouble removing joint on steering idler!  (Read 820 times)

0 Members and 1 Guest are viewing this topic.

El_Swervo

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Farnborough Hants
  • Posts: 98
    • Omega estate, CDX 2.6
    • View Profile
Having trouble removing joint on steering idler!
« on: 16 October 2010, 16:41:58 »
Hello All,

The second current problem with my Omega right now is a very worn out steering idler.

I have bought a replacement and tried to remove the old unit. However, It wont come apart. I have tried 3 different ball joint type splitters, the hammer/prybar method and some brute force and ignorance, none of which have done the job.

Will I have to remove the whole lot and do it on a bench or does anybody have a good tip for stubborn steering idlers? I have looked on the forum for an answer to no avail, if there is a thread could someone put me in the right place!
Logged

Varche

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • middle of Andalucia
  • Posts: 14000
  • What is going to break next?
    • Golf Estate
    • View Profile
Re: Having trouble removing joint on steering idler!
« Reply #1 on: 16 October 2010, 18:12:27 »
You are not alone with this problem.

When I did mine I applied plus gas (not useless WD40) and then used the time honoured method of two hammers. Hitting both sides simulaneously. I nearly gave up about a thousand times and then bingo it came free. Suggest you try the same.
Logged
The biggest joke on mankind is that computers have started asking humans to prove that they aren’t a robot.

PhilRich

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • A bit further North of the Back of Beyond!
  • Posts: 10338
    • Mk 2 Volvo V70
    • View Profile
Re: Having trouble removing joint on steering idler!
« Reply #2 on: 16 October 2010, 18:34:33 »
Quote
Hello All,

The second current problem with my Omega right now is a very worn out steering idler.

I have bought a replacement and tried to remove the old unit. However, It wont come apart. I have tried 3 different ball joint type splitters, the hammer/prybar method and some brute force and ignorance, none of which have done the job.

Will I have to remove the whole lot and do it on a bench or does anybody have a good tip for stubborn steering idlers? I have looked on the forum for an answer to no avail, if there is a thread could someone put me in the right place!




Have you looked at this? :-? :y

http://www.omegaowners.com/forum/YaBB.pl?num=1268602974
Logged
If it ain't broke keep fixing it 'til it is!

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 107031
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: Having trouble removing joint on steering idler!
« Reply #3 on: 16 October 2010, 19:06:22 »
Using the method in the guide (aka, the DTM Method), its relative easy :y
Logged
Grumpy old man

2woody

  • Omega Baron
  • *****
  • Offline Offline
  • Northumberland
  • Posts: 2374
    • View Profile
Re: Having trouble removing joint on steering idler!
« Reply #4 on: 16 October 2010, 21:32:08 »
the secret is a light hammer - it's the sharpness of the shock that does the trick, rather than the weight of the blow
Logged

El_Swervo

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Farnborough Hants
  • Posts: 98
    • Omega estate, CDX 2.6
    • View Profile
Re: Having trouble removing joint on steering idler!
« Reply #5 on: 17 October 2010, 14:21:55 »
Thanks Men!

I will have a go at this asap, I gave up first time after two hours! now every bump,(read pot hole!), and speed hump is cringeworthy. :o

Will post results and thanks post job!

Thank you all again
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.028 seconds with 17 queries.