Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[TheBoy]

Big thanks to Jimbob for your help tonight many thanks all sorted now

And the result/fix?

[b4ndit]

all fixed it was plugs there were a couple of codes in there which were random codes but all working and a1 very happy plugs are only 6 months old as well

[Jimbob]

codes were :

P0155 - O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
 (08) - Intermittent

P0300 - Random/Multiple Cylinder Misfire Detected
 (01) - Not present

P0306 - Cylinder 6 Misfire Detected
 (01) - Not present

P0340 - Camshaft Position Sensor Circuit High Input
 (01) - Not present

[Jimbob]

Live Data :

Battery Voltage   13.0 V
Main Relay   Active
Fuel Pump Relay   Active
APP Sensor 1 (Accelerator Pedal Position)   1.00 V
APP Sensor 2 (Accelerator Pedal Position)   0.51 V
Calculated Pedal Position   0%
APP at Idle Position (Accelerator Pedal Position)   Active
TP Sensor 1 (Throttle Position)   0.66 V
TP Sensor 2 (Throttle Position)   4.33 V
Calculated Throttle Position   1%
Throttle Position   Idle
Engine Speed   689 RPM
Mass Air Flow Sensor   1.43 V
Mass Air Flow Sensor   15 kg/h
Coolant Temperature   1.49 V
Coolant Temperature   71 °C
Intake Air Temperature   3.33 V
Intake Air Temperature   25 °C
Torque Control   Inactive
Tank Sensor   3.53 V
Tank Sensor   5 L
Park/Neutral Switch   P - N  0V
A/C Information Switch   Inactive
Brake Switch 1   Inactive
Brake Switch 2   Inactive
Clutch Switch   Active
Vehicle Speed   0 km/h
Cruise Control Tip Switch   Inactive
Cruise Control   Inactive
Vehicle Speed in Cruise Control Range   Inactive
Fuel Tank Ventilation Valve   5%
Knock Control   Inactive
B1S1 O2 Sensor Heater (Bank 1 Sensor 1)   Active
B1S1 O2 Sensor (Bank 1 Sensor 1)   488 mV
B1S1 Air/Fuel Ratio (Bank 1 Sensor 1)   Rich
B1S2 O2 Sensor Heater (Bank 1 Sensor 2)   Inactive
B1S2 O2 Sensor (Bank 1 Sensor 2)   488 mV
B1S2 Air/Fuel Ratio (Bank 1 Sensor 2)   Lean
B2S1 O2 Sensor Heater (Bank 2 Sensor 1)   Active
B2S1 O2 Sensor (Bank 2 Sensor 1)   684 mV
B2S1 Air/Fuel Ratio (Bank 2 Sensor 1)   Rich
B2S2 O2 Sensor Heater (Bank 2 Sensor 2)   Inactive
B2S2 O2 Sensor (Bank 2 Sensor 2)   488 mV
B2S2 Air/Fuel Ratio (Bank 2 Sensor 2)   Lean
O2 Sensor Loop   Closed
B1 Long Term Fuel Trim (Bank 1)   -1%
B2 Long Term Fuel Trim (Bank 2)   -1%
B1 Short Term Fuel Trim (Bank 1)   -7%
B2 Short Term Fuel Trim (Bank 2)   -6%
Requested Torque (Automatic Transmission)   199 Nm
Requested Torque (Traction Control)   199 Nm
A/C Relay (Air Conditioning)   Inactive
Malfunction Indicator (MI)   Off
Service Vehicle Soon (SVS) Indicator   Off
Intake Manifold Valve 1   Inactive
Intake Manifold Valve 2   Inactive
Engine Speed   689 RPM
Desired Idle Speed   680 RPM
Idle Speed Offset   0 RPM
Idle Speed Offset   Cold Start
Vehicle Acceleration   0.0 m/s2
Ignition Dwell Angle   1.9 ms
Injector Time   3.9 ms
Ignition Spark Angle   4.2 °CA
B1 Knock Sensor Signal (Bank 1)   0.0 V
B2 Knock Sensor Signal (Bank 2)   0.0 V
Relative Engine Load   6%
Ignition Status   On  12V
Normal Engine Operating Temperature   Inactive
ETC Limp Home Mode (Electronic Throttle Control)   Inactive
Ambient Temperature   12 °C
Vehicle Speed Pulse   Not Received
Dec. Fuel Cutoff (Deceleration)   Inactive
Actual Accelerating Enrichment   0
Fuel Tank Ventilation Valve   Active

[Jimbob]

All codes / trims reset so can monitor for any reoccurance.

[b4ndit]

Thanks for the info Jimbob will keep my eye on things

[TheBoy]

If those live readings were before the codes were cleared, all well and good

If they were after the codes were cleared, revisit Mr Greedy in a week or 2, and get live data readings before clearing codes

[b4ndit]

think they were after the codes were cleared

[TheBoy]

think they were after the codes were cleared

Bugger.

Give it a week, then revisit. And slap him repeatedly for doing it in the wrong order

[b4ndit]

I could have it all the wrong way round 

[TheBoy]

I could have it all the wrong way round 

Slap him anyway. He probably deserves it

[b4ndit]

I cant do that he's a very nice man

[Jimbob]

I did clear the codes....forgetting that reset the trims by default

sorry

As I said at the time, anything untoward, and we can reread from a clean slate

[b4ndit]

Thanks Jimbob will be in touch if anything happens

[TheBoy]

I did clear the codes....forgetting that reset the trims by default

sorry

As I said at the time, anything untoward, and we can reread from a clean slate

Sounds like the perfect excuse for local Chester members to have a mini meet

...see, you did it on purpose, really