Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: [1]   Go Down

Author Topic: Help with a locking wheel nut please!?  (Read 1281 times)

0 Members and 1 Guest are viewing this topic.

Varche

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • middle of Andalucia
  • Posts: 13956
  • What is going to break next?
    • Golf Estate
    • View Profile
Help with a locking wheel nut please!?
« on: 24 February 2013, 12:04:39 »
To say I hate these things would be an undestatement.

Went to change my rear wiper on my 4x4 . Couldn't - insufficient room without removing spare wheel bolted to rear door. Couldn't get spare wheel off as locking wheel nut key won't undo "bolt". It is a standard cylinder with a key that inserts in the end of the barrel. Once removed you can then get a wheel nut socket on it. I had it off 12 months ago so I know it works and is the right and only key. No manufacturer name on the device or key. Key just has R009 on it.

I have had it soaking in plus gas for 24 hours and also tried heating it up. also gently hammer tapping. My fall back I guess is to try and drill  or angle grind the sleeve off. Access is fairly good compared to say on an Omega alloy wheel.

Any suggestions welcome!
Logged
The biggest joke on mankind is that computers have started asking humans to prove that they aren’t a robot.

omega3000

  • Guest
Re: Help with a locking wheel nut please!?
« Reply #1 on: 24 February 2013, 12:13:26 »
Hateful things and would never fit them , burnt the ones off my carlton with a gas torch ..made the wheels a bit black but it was the only way  >:( . Some have hammered a socket over it once the outer ring is cut off  :-\
Logged

Varche

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • middle of Andalucia
  • Posts: 13956
  • What is going to break next?
    • Golf Estate
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #2 on: 24 February 2013, 12:15:06 »
Haven't got access to welding torch.

Logged
The biggest joke on mankind is that computers have started asking humans to prove that they aren’t a robot.

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39752
    • ML350 TDM SmartRoadster
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #3 on: 24 February 2013, 12:17:02 »
Quote from: Varche on 24 February 2013, 12:04:39
.... My fall back I guess is to try and drill  or angle grind the sleeve off. Access is fairly good compared to say on an Omega alloy wheel.

Any suggestions welcome!

Grind/saw the end of sleeve off  ;)
Logged

YZ250

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Oxford/Bucks border
  • Posts: 4582
    • Black 3.2 Elite Estate
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #4 on: 24 February 2013, 12:24:19 »
I used to have these on my caravan leg locks. The only way I could remove them was by pulling the sleeve up at the same time as pulling the key and barrel out, if that makes sense. In other words, it was a two handed job. You may have tried that though.  :-\
Logged
My fun car is a 2020 Bmw F32 430d M Sport with indicators.
My cruiser is an Audi A6 Avant S Line Black Edition with indicators.

Varche

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • middle of Andalucia
  • Posts: 13956
  • What is going to break next?
    • Golf Estate
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #5 on: 24 February 2013, 13:43:50 »
Angle grinded off.

Thanks
Logged
The biggest joke on mankind is that computers have started asking humans to prove that they aren’t a robot.

kevinp58

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • kent
  • Posts: 1462
    • 2002 3.2 elite
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #6 on: 24 February 2013, 13:52:34 »
Whack an old large screwdriver into it and it should then turn
Logged

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39752
    • ML350 TDM SmartRoadster
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #7 on: 24 February 2013, 13:57:54 »
Quote from: kevinp58 on 24 February 2013, 13:52:34
Whack an old large screwdriver into it and it should then turn

They already turn. Putting the key in allows the barrel and sleeve to pull straight out of the end of the nut/bolt.  ;)
Logged

omega3000

  • Guest
Re: Help with a locking wheel nut please!?
« Reply #8 on: 24 February 2013, 15:30:32 »
Logged

scimmy_man

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • yorkshire
  • Posts: 1111
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #9 on: 25 February 2013, 19:12:20 »
a slide hammer will pull the middle out, I have a few sets of those on various cars, make sure the lock is well greased.
Logged

Webby the Bear

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Northampton
  • Posts: 12729
    • 2000 (W Reg.) 2.5 V6 CD
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #10 on: 25 February 2013, 19:20:47 »
i paid £5 for the guy at scotts tyres northampton to get mine out as i lost the nut key thingy. took him 10 mins where as the bloke at ATS tried for 40 mins with no success :y :y :y
Logged
RIP Paul Lovejoy

scimmy_man

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • yorkshire
  • Posts: 1111
    • View Profile
Re: Help with a locking wheel nut please!?
« Reply #11 on: 26 February 2013, 18:50:43 »
I think its more to do with the standards of monkey employed?
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.014 seconds with 17 queries.