Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Search the maintenance guides for answers to 99.999% of Omega questions

Pages: [1] 2  All   Go Down

Author Topic: Rear wheel bearing change continued  (Read 4847 times)

0 Members and 1 Guest are viewing this topic.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1084
    • 2.6 Y26SE Elegance 2001
    • View Profile
Rear wheel bearing change continued
« on: 16 May 2019, 19:04:33 »
So, old bearing on the floor, nothing broken yet. I have tools to push new bearing in and I am now designin a nut system to pull the hub back in. Next I should install the flange to the inner side. How that tool should look like?
Logged

Nick W

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chatham, Kent
  • Posts: 11051
    • Ghastly 1.0l Focus
    • View Profile
Re: Rear wheel bearing change continued
« Reply #1 on: 16 May 2019, 23:19:29 »
I use the old inner bearing race as a spacer to pull the hub back into place using its own nut. The race does need to be a loose fit, which is acheived by cutting a slot in it. Which is the easy way to get it off the hub.
Logged

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1084
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Rear wheel bearing change continued
« Reply #2 on: 17 May 2019, 06:12:32 »
Hello, yes - my idea was to use id 34.5 spacers which are a bit larger than the outer dia of the groove part of the hub. As the dia 39 part of the hub (where inner race of baring sits) is shorter than the bearing there is no need to "loose fit". Perhaps estate is different than saloon or I misundesrtood again. However, my problem is get the flange back to the hub after having installed to hub to the bearing. How to do that?
Logged

Nick W

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chatham, Kent
  • Posts: 11051
    • Ghastly 1.0l Focus
    • View Profile
Re: Rear wheel bearing change continued
« Reply #3 on: 17 May 2019, 07:10:58 »
Now I'm confused, the drive flange is easy: push it as far onto the hub splines as you can, tap it home with a mallet and tighten the nut to the specified torque setting.


Spacers for pulling the hub into the bearing go against the inner race of the new bearing. The spacer needs to be a loose fit on the hub so you can get it off easily. I have two in my bearing kit: one with a slot cut in it to get off the hub originally; and another, that my assistant removed with a puller, that I bored out in the lathe.
Logged

biggriffin

  • Omega Lord
  • *****
  • Offline Offline
  • huntingdon, Hoof'land
  • Posts: 9844
    • It's Insignificant
    • View Profile
Re: Rear wheel bearing change continued
« Reply #4 on: 17 May 2019, 07:57:22 »
All I do,is dress the hub with a bit of 800 grade wet/dry that's got oil on, then push the hub back in, piece of timber on the hub, then whack it in with a hammer, tighten it up with a windy gun,  :y
Logged
Hoof'land storeman.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1084
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Rear wheel bearing change continued
« Reply #5 on: 17 May 2019, 09:45:53 »
Quote from: Nick W on 17 May 2019, 07:10:58
Now I'm confused, the drive flange is easy: push it as far onto the hub splines as you can, tap it home with a mallet and tighten the nut to the specified torque setting.


Spacers for pulling the hub into the bearing go against the inner race of the new bearing. The spacer needs to be a loose fit on the hub so you can get it off easily. I have two in my bearing kit: one with a slot cut in it to get off the hub originally; and another, that my assistant removed with a puller, that I bored out in the lathe.

My turn to be confused, the diameter of the drive shaft (of that part which goes in to the inner race) is 39 mm + some hundreds. That part newer come through the inner race as the length of that part is 38 mm and the length of bearing is 45mm. This 45 is measured from the new bearing, perhaps it is wrong part. Have to measure the length of the old bearing when back home.
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 29872
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Rear wheel bearing change continued
« Reply #6 on: 17 May 2019, 10:05:44 »
Saloon and estates use different bearings... The estate ones are longer ie they support a longer shaft length...

You have the wrong bearing...

Estate is same size as this:
http://vi.raptor.ebaydesc.com/ws/eBayISAPI.dll?ViewItemDescV4&item=312531364962&category=174097&pm=1&ds=0&t=1558083811991&cspheader=1

Hth.  :y
Logged
Onanists always think outside the box.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1084
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Rear wheel bearing change continued
« Reply #7 on: 17 May 2019, 10:12:35 »
OK, then I can understand what Nick W means... Sorry for that.

What is the length of Saloon bearing?
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 29872
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Rear wheel bearing change continued
« Reply #8 on: 17 May 2019, 10:18:44 »
Quote from: polilara on 17 May 2019, 10:12:35
OK, then I can understand what Nick W means... Sorry for that.

What is the length of Saloon bearing?
39mm as per:

https://www.ebay.co.uk/itm/Vauxhall-Omega-1994-2003-Rear-Wheel-Bearing-Kit-/302340675199
Logged
Onanists always think outside the box.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1084
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Rear wheel bearing change continued
« Reply #9 on: 17 May 2019, 10:49:46 »
OK thanks, let's see, after having measured the old one I know what I really had there. This Saloon link bearing fits perhaps to some front wheel driven cars, too, because of two Seeger Rings and a cotter pin??
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 29872
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Rear wheel bearing change continued
« Reply #10 on: 17 May 2019, 11:08:31 »
Quote from: polilara on 17 May 2019, 10:49:46
OK thanks, let's see, after having measured the old one I know what I really had there. This Saloon link bearing fits perhaps to some front wheel driven cars, too, because of two Seeger Rings and a cotter pin??
The link was to demonstrate the size... The picture may not be entirely accurate  :y
Logged
Onanists always think outside the box.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1084
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Rear wheel bearing change continued
« Reply #11 on: 17 May 2019, 11:24:49 »
OK, clear, sometimes too much over thinking...
Logged

Doctor Gollum

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 29872
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: Rear wheel bearing change continued
« Reply #12 on: 17 May 2019, 11:58:35 »
Quote from: polilara on 17 May 2019, 11:24:49
OK, clear, sometimes too much over thinking...
Perhaps, but questioning is a way to learn ;)
Logged
Onanists always think outside the box.

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1084
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Rear wheel bearing change continued
« Reply #13 on: 18 May 2019, 06:25:27 »
So, old bearing is Od 74 Id 39 L 39, hub length is 38 So there is 1mm Gap after having installed the flange, logical. And loose fit of spacer needed as Nick W said.
Logged

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1084
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Rear wheel bearing change continued
« Reply #14 on: 21 May 2019, 17:27:34 »
Real progress; bearing, hub and flange installed. Thanks for all tips. Next task is to tighten the nut to 300Nm. Good ideas welcome, I am workin on the floor.
Logged
Pages: [1] 2  All   Go Up
« previous next »
 

Page created in 0.02 seconds with 21 queries.