Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: 1 [2]  All   Go Down

Author Topic: P0340 Cam sensor code after belt change  (Read 4617 times)

0 Members and 1 Guest are viewing this topic.

Doctor Gollum

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • In a colds and darks puddleses
  • Posts: 29859
  • If you can't eat them, join them...
    • Feetses.
    • View Profile
Re: P0340 Cam sensor code after belt change
« Reply #15 on: 25 September 2019, 18:45:43 »
They are numbered 1 through 4 according to the cam position  ;)

1 and 4 are the exhaust ones, and 2 and 3 are the inlet ones ;)
Logged
Onanists always think outside the box.

Jan Suhr

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Nyköping, Sweden
  • Posts: 420
    • 2 Omega Caravans 3.2 V6
    • View Profile
Re: P0340 Cam sensor code after belt change
« Reply #16 on: 25 September 2019, 18:50:24 »
Quote from: jonathanh on 25 September 2019, 18:14:36
On the left hand cam use marking 3 the red one you have marked. On right hand cam use mark 4 the red one not the green.  It would be good for someone else to confirm too as I am going from memory- last time I changed a belt was two years ago!!!

I agree, the picture shows the correct position with the red arrows since this was before I took it apart. The tricky bit that fooled me is that the wheels 3 & 4 are the same. On wheel 3 there are the numbers 3 4 stamped at the left mark, and that's why I positioned it at the green arrow since the numbers are there. Whey they did so is a bit unlogical in my mind. But maybe the 4 had to be where it is since there is a big hole where it supposed to be.

Anyway I correct this tomorrow and let you know if it works better after that.
Logged
Jan Suhr
Stockholm, Sweden
www.protouring.se

YZ250

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Oxford/Bucks border
  • Posts: 4588
    • Black 3.2 Elite Estate
    • View Profile
Re: P0340 Cam sensor code after belt change
« Reply #17 on: 25 September 2019, 20:42:29 »
Quote from: jonathanh on 25 September 2019, 18:14:36
On the left hand cam use marking 3 the red one you have marked. On right hand cam use mark 4 the red one not the green.  It would be good for someone else to confirm too as I am going from memory- last time I changed a belt was two years ago!!!

 :y
Cam 3 is the long notch and cam 4 is the short notch, so the red arrows are correct as said.  :y
Logged
My fun car is a 2020 Bmw F32 430d M Sport with indicators.
My cruiser is an Audi A6 Avant S Line Black Edition with indicators.

Jan Suhr

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Nyköping, Sweden
  • Posts: 420
    • 2 Omega Caravans 3.2 V6
    • View Profile
Re: P0340 Cam sensor code after belt change
« Reply #18 on: 26 September 2019, 14:57:40 »
Now the cams are properly set and the engine runs and sounds like it should.

Feeling good again  :)
Logged
Jan Suhr
Stockholm, Sweden
www.protouring.se

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1082
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: P0340 Cam sensor code after belt change
« Reply #19 on: 30 September 2019, 14:55:39 »
Good that solved, is the belt more "in front" now? Remember I thought it was a bit back.
Logged

Jan Suhr

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Nyköping, Sweden
  • Posts: 420
    • 2 Omega Caravans 3.2 V6
    • View Profile
Re: P0340 Cam sensor code after belt change
« Reply #20 on: 30 September 2019, 15:16:53 »
Quote from: polilara on 30 September 2019, 14:55:39
Good that solved, is the belt more "in front" now? Remember I thought it was a bit back.

Yes thanks for asking,

Everything in order and proper alignment. The belt runs good on the idlers. The old kit wasn't the correct one for this engine. It had the earlier kit and it should have the later. I expect it to last 60000km as  it should. This is my winter car, instead of changing tyres I swap cars  ;D

When it's duties is over in the spring I will check the status on the cam belt.
Logged
Jan Suhr
Stockholm, Sweden
www.protouring.se

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1082
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: P0340 Cam sensor code after belt change
« Reply #21 on: 30 September 2019, 17:46:28 »
OK, hope you have spikes and LSD, some snow will come soon...
Logged
Pages: 1 [2]  All   Go Up
« previous next »
 

Page created in 0.014 seconds with 17 queries.