Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please play nicely.  No one wants to listen/read a keyboard warriors rants....

Pages: [1] 2  All   Go Down

Author Topic: Changed Head Gaskets Now It Won't Start!  (Read 1847 times)

0 Members and 1 Guest are viewing this topic.

3.0V6Elite

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Salisbury
  • Posts: 108
    • View Profile
Changed Head Gaskets Now It Won't Start!
« on: 22 March 2009, 19:05:36 »
After a week long battle I have finally finished installing the new head gaskets, oil cooler and cam belt to my 3.0 V6 Elite.



 All went well apart from not tightening up the coolant bridge properly, which I noticed after putting coolant in and springing a leak  :-[. The problem I now have is that it won't start. She turns over fine and there are no faults coming up on the computer. I do however have an issue with electrics, in that 2 connections on the engine are now missing  :question.

The connections in question are these





And here is where they are in relation to each other



I now where one connection is, its here



and here



I have somehow managed to shear it off but can't find the other end. I know it is for the orange female connector pictured above because it fits like a glove, the thing is I found it at the back of the engine... don't ask! As to where the other connector is, your guess is as good as mine.

My question is, would the lack of anything on these connections stop the engine from starting, and are they supposed to connect to each other as they are both 3 pin?
Logged

philhoward

  • Senior Member
  • ****
  • Offline Offline
  • Staffs
  • Posts: 939
  • Love the engines, so put one in something else..
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #1 on: 22 March 2009, 19:09:53 »
One is the throttle pot - and will probably upset it.  Not sure on the other one...hope for your sake it isn't the crank sensor..
Logged
Running an X30XE in a Reliant Scimitar GTE as I can't have an Omega as a company car...

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39774
    • ML350 TDM SmartRoadster
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #2 on: 22 March 2009, 19:12:48 »
Quote
One is the throttle pot - and will probably upset it.  Not sure on the other one...hope for your sake it isn't the crank sensor..

Throttle pot upsets the gearbox too and it will only drive in 3rd ...... well it did on mine when I left it off after my cam belt change.  ::)
Logged

Elite Pete

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chester
  • Posts: 19580
  • My spider senses are tingling
    • Audi SQ5 GSX1400
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #3 on: 22 March 2009, 19:30:20 »
Throttle boddies and looks like knock sensor. Im suprised there's no codes.
Logged
Retired

3.0V6Elite

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Salisbury
  • Posts: 108
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #4 on: 22 March 2009, 19:39:25 »
Quote
One is the throttle pot - and will probably upset it.  Not sure on the other one...hope for your sake it isn't the crank sensor..
No, the crank sensor has been replaced recently.

Does anyone have any idea where the connector for the throttle bodies originates from as I can't find it anywhere?
Logged

3.0V6Elite

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Salisbury
  • Posts: 108
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #5 on: 22 March 2009, 21:12:42 »
On looking at my workshop manual CD the connection on the throttle body is for the throttle valve potentiometer, does anyone know where that connection originates?
Logged

Darth Loo-knee

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Death Star
  • Posts: 18826
  • Jammie smells of Pooh....
    • TIE Fighter
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #6 on: 22 March 2009, 21:24:55 »
Going of the top of my head here so bear with me...

The Rear Multi Ram Connection easily falls down the back

The connector on the front passenger side of the throttle body goes into the cable tray, the same place as that cable you have sheared, which looks like a knock sensor. I might have one of those but wont be able to get it until Wednesday.
Hope this helps
Daz :y  
Logged
Everything to do with Omega's. Breaking, Servicing from Cambelts to Oil Changes... Please Pm me for details...

3.0V6Elite

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Salisbury
  • Posts: 108
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #7 on: 22 March 2009, 21:32:16 »
Quote
Going of the top of my head here so bear with me...

The Rear Multi Ram Connection easily falls down the back

The connector on the front passenger side of the throttle body goes into the cable tray, the same place as that cable you have sheared, which looks like a knock sensor. I might have one of those but wont be able to get it until Wednesday.
Hope this helps
Daz :y  
That could help mate, I did have trouble finding the connection for the rear of the multiram but found it in the end, that was a 2 pin connector. I will have another look around for the connector for the throttle body but I have looked over and over and can't find it. As for the knock sensor, that does sound plausable but which one?
Logged

Darth Loo-knee

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Death Star
  • Posts: 18826
  • Jammie smells of Pooh....
    • TIE Fighter
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #8 on: 22 March 2009, 21:39:40 »
If you look from the front of your car into the engine area, right infront of the passenger cam cover there is a wire that runs in between the cam cover and Cambelt Housing Plate.. that is the one that seems you have sheared which should connect to the end of the wire tray. In that same wire tray there should be another wire which is quiet long that will plug into the throttle body :y
Logged
Everything to do with Omega's. Breaking, Servicing from Cambelts to Oil Changes... Please Pm me for details...

3.0V6Elite

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Salisbury
  • Posts: 108
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #9 on: 22 March 2009, 21:49:58 »
Quote
If you look from the front of your car into the engine area, right infront of the passenger cam cover there is a wire that runs in between the cam cover and Cambelt Housing Plate.. that is the one that seems you have sheared which should connect to the end of the wire tray. In that same wire tray there should be another wire which is quiet long that will plug into the throttle body :y
I am sure that that knock secsor is intact but I will check.
Logged

Darth Loo-knee

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Death Star
  • Posts: 18826
  • Jammie smells of Pooh....
    • TIE Fighter
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #10 on: 22 March 2009, 21:55:19 »
Well have a llok where the wire is then that goes infront on the passenger cam cover. At first glance I did think the connector you have cut was a crank sensor :-?
Logged
Everything to do with Omega's. Breaking, Servicing from Cambelts to Oil Changes... Please Pm me for details...

3.0V6Elite

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Salisbury
  • Posts: 108
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #11 on: 23 March 2009, 09:17:42 »
I managed to find the 2 offending wires this morning, I had inadvertantly connected the 2 wires together  [smiley=rolleyes.gif]. They are now connected to where they should be i.e. the left hand cam shaft knock sensor and the throttle valve potentiometer. However I have ran the battery down trying to start it yesterday so will not be able to try and fire it up until this evening after work.

Wish me luck  :y.
Logged

3.0V6Elite

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Salisbury
  • Posts: 108
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #12 on: 23 March 2009, 21:23:26 »
Well, charged the battery up this evening after work and was really looking forward to firing up the beast. Put the battery on with a big grin on my face, key went in the ignition and I tried to start it. It turns over really strong but will not fire up. Checked to see if I was getting a spark, nothing. Did the old paperclip test and am getting code 19. Am I right in thinking this is the crank sensor and if so would this explain not getting a spark? PLEASE HELP ME  :'(
Logged

Entwood

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • North Wiltshire
  • Posts: 19566
  • My Old 3.2 V6 Elite (LPG)
    • Audi A6 Allroad 3.0 DTI
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #13 on: 23 March 2009, 21:36:37 »
Quote
Well, charged the battery up this evening after work and was really looking forward to firing up the beast. Put the battery on with a big grin on my face, key went in the ignition and I tried to start it. It turns over really strong but will not fire up. Checked to see if I was getting a spark, nothing. Did the old paperclip test and am getting code 19. Am I right in thinking this is the crank sensor and if so would this explain not getting a spark? PLEASE HELP ME  :'(

Most certainly yes ...  the system will not give a spark if it detects a problem .. and it doesn't know where the bits are in relation to each other if it doesn't know the rotational position of the crankshaft

Lots of threads about code 19 .. and a how to in the guides section... make sure you obey the instructions about the cable routing .. :y :y :y

HTH
Logged

3.0V6Elite

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Salisbury
  • Posts: 108
    • View Profile
Re: Changed Head Gaskets Now It Won't Start!
« Reply #14 on: 23 March 2009, 22:48:30 »
That will probably explain why I found the sheared 3 pin plug at the back of the engine, it must have been from the crank sensor  ::).
Logged
Pages: [1] 2  All   Go Up
« previous next »
 

Page created in 0.011 seconds with 17 queries.