Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1] 2  All   Go Down

Author Topic: MAF on a TD  (Read 1307 times)

0 Members and 1 Guest are viewing this topic.

Welung666

  • Guest
MAF on a TD
« on: 15 June 2009, 13:39:38 »
My 99 2.5 TD has the MAF unplugged, has been since I've had it. I plugged it in and it went straight into limp mode, unplugged it and it's fine again. Would a replacement cure the limp mode or would I be better off just leaving it as it is?
Logged

zirk

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Epping Forest
  • Posts: 11436
  • 3.2 Manual Special Saloon ReMapped and LPG'd and
    • 3.2 Manual Special Estate
    • View Profile
Re: MAF on a TD
« Reply #1 on: 15 June 2009, 14:26:48 »
Quote
My 99 2.5 TD has the MAF unplugged, has been since I've had it. I plugged it in and it went straight into limp mode, unplugged it and it's fine again. Would a replacement cure the limp mode or would I be better off just leaving it as it is?

Ive had Maf issues on a TD before, didn't seem to make any difference on mine weither it was pluged in or not.
Logged

Welung666

  • Guest
Re: MAF on a TD
« Reply #2 on: 15 June 2009, 16:25:45 »
Quote
Quote
My 99 2.5 TD has the MAF unplugged, has been since I've had it. I plugged it in and it went straight into limp mode, unplugged it and it's fine again. Would a replacement cure the limp mode or would I be better off just leaving it as it is?

Ive had Maf issues on a TD before, didn't seem to make any difference on mine weither it was pluged in or not.

This one does matter. Plugged in and it struggles to get up to 1.5k rpm and won't go further. Turbo doesn't kick in until nearly 2k so it's like driving a snail hence me leaving it unplugged :P
Logged

charlie

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • sunderland
  • Posts: 630
    • View Profile
Re: MAF on a TD
« Reply #3 on: 15 June 2009, 16:28:36 »
when my maf was broken it would rev freely when not in gear, but when in gear would only go to 2k revs. changed it sorted .PS these are over £200 at the stealers
Logged

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 106886
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: MAF on a TD
« Reply #4 on: 15 June 2009, 19:02:56 »
the substitute values are reasonable, so can drive with maf unplugged.  Slightly more responsive, and far more likely to pass smoke test with working maf though.


Notice, being BMW firmware, the EML doesn't come on, even though it knows there is a fault ;)
Logged
Grumpy old man

semisheen

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Chesterfield
  • Posts: 213
    • View Profile
Re: MAF on a TD
« Reply #5 on: 15 June 2009, 22:19:14 »
Sorry to Hijack this post but .......could it be the Maf why im only getting an avarage of "this week" 22.9 to the gallon ?
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 33985
  • Git!
    • View Profile
Re: MAF on a TD
« Reply #6 on: 16 June 2009, 11:34:40 »
Unplug it and see.

The MAF on this unit does little more than limit the fuel injected if the air flow is low to stop smoke (unburnt fuel) exiting the exhaust.

And yes, typical BMW setup, no fault light even if there is a fault!
Logged

Stoph

  • Newbie
  • *
  • Offline Offline
  • 0
  • Posts: 14
    • View Profile
Re: MAF on a TD
« Reply #7 on: 16 June 2009, 11:39:37 »
My 525 TDS had the MAF unplugged when I bought it, plugged back in went into limp home mode...which is why the idiot that sold it had unplugged it ! It was sort of ok with it unplugged but undriveable with it connected... with a new MAF fitted its a completely different car... best price I found and with quick delivery too was £157 including delivery from a bloke called Paul. cant remember his trading name but number is 0208 462 2543..  Pull off the old MAF it should be a Pierburg.. code 7.22184.50.0 he will ask you to check before ordering as obviously doesnt want to send the wrong one!

HTH  Chris
Logged

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 106886
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: MAF on a TD
« Reply #8 on: 16 June 2009, 18:58:49 »
Quote
Unplug it and see.

The MAF on this unit does little more than limit the fuel injected if the air flow is low to stop smoke (unburnt fuel) exiting the exhaust.

And yes, typical BMW setup, no fault light even if there is a fault!
It defo responds better with a workign MAF - I had a habit of always forgetting to plug it back in (and no fault light to remind me!), and it was a subtle sluggishness that would remind me...
Logged
Grumpy old man

Welung666

  • Guest
Re: MAF on a TD
« Reply #9 on: 16 June 2009, 19:17:29 »
It's only sub-1500 rpm thats a bit sluggish, I'll have to see about picking a MAF up.
Logged

Pitchfork

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Tadley (near Basingrad)
  • Posts: 2498
  • Barndances & Morris
    • View Profile
Re: MAF on a TD
« Reply #10 on: 16 June 2009, 19:19:37 »
As I recall, early TDs did not have a MAF
Did that make them more sluggish than the later ones?
Logged
Almost famous!   www.pitchforkband.co.uk Guitar & PA Amps repaired & serviced
Ears pierced while you wait. PAT & Valve testing

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 33985
  • Git!
    • View Profile
Re: MAF on a TD
« Reply #11 on: 16 June 2009, 19:21:45 »
Quote
Quote
Unplug it and see.

The MAF on this unit does little more than limit the fuel injected if the air flow is low to stop smoke (unburnt fuel) exiting the exhaust.

And yes, typical BMW setup, no fault light even if there is a fault!
It defo responds better with a workign MAF - I had a habit of always forgetting to plug it back in (and no fault light to remind me!), and it was a subtle sluggishness that would remind me...

Probably because the default is to drop the fueling slightly in order to stop it smoking on a default value
Logged

Omegatoy

  • Omega Baron
  • *****
  • Offline Offline
  • UK
  • Posts: 3688
    • View Profile
Re: MAF on a TD
« Reply #12 on: 16 June 2009, 19:22:30 »
no it means we can get less faults!!! ;D :y
Logged

Pitchfork

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Tadley (near Basingrad)
  • Posts: 2498
  • Barndances & Morris
    • View Profile
Re: MAF on a TD
« Reply #13 on: 16 June 2009, 19:24:49 »
What causes a MAF to fail?
What fault code is generated?
Would hydrolocking have caused any damage?
Logged
Almost famous!   www.pitchforkband.co.uk Guitar & PA Amps repaired & serviced
Ears pierced while you wait. PAT & Valve testing

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 106886
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: MAF on a TD
« Reply #14 on: 16 June 2009, 19:55:33 »
Quote
It's only sub-1500 rpm thats a bit sluggish, I'll have to see about picking a MAF up.
No, its not that, its a subtle lack of responsiveness when its normally in its power band
Logged
Grumpy old man
Pages: [1] 2  All   Go Up
« previous next »
 

Page created in 0.059 seconds with 20 queries.