Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: [1]   Go Down

Author Topic: td- lumpy tickover  (Read 1018 times)

0 Members and 2 Guests are viewing this topic.

raywilb

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • york
  • Posts: 1874
    • DS DS4
    • View Profile
td- lumpy tickover
« on: 04 November 2009, 20:54:57 »
my tractor is ticking over crappy. showing 96 a egr  fault - could that be the problem  when driven goes well. welcome any ideas
Logged

Ian_D

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • York
  • Posts: 2432
    • View Profile
Re: td- lumpy tickover
« Reply #1 on: 05 November 2009, 01:13:04 »
Hehe... was just thinking 'ah I will tell Ray that someone else has a problem like him....' then realized it was you Ray!  ;D

Just for a bit more info, the idle is fine for about 8 seconds, then it has a 2-3 second period running a bit lumpy, then its fine again. This cycle repeats over and over.

If you press the accelerator down a fraction and hold the revs at about 850rpm, it runs extremely rough. :-/

There was some fault codes that came up, will dig them out and post them in a sec…
Logged
[size=12]
LMF are utter rubbish - dont buy steering idlers from them! You've been warned![/size]

Ian_D

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • York
  • Posts: 2432
    • View Profile
Re: td- lumpy tickover
« Reply #2 on: 05 November 2009, 01:21:49 »
Total number of fault codes:  3

96 - Exhaust Gas Recirculation (EGR) Valve Out Of Range
Not present

92 - CRC Control Device Open Or Voltage High
Present

64 - Fuel Quantity Control Out Of Range
Not present
Logged
[size=12]
LMF are utter rubbish - dont buy steering idlers from them! You've been warned![/size]

raywilb

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • york
  • Posts: 1874
    • DS DS4
    • View Profile
Re: td- lumpy tickover
« Reply #3 on: 05 November 2009, 07:31:02 »
cheers for that ian youv,e explained it better than me, code 92 is a code i,d always have with not having cruise control fitted.  :y :y
Logged

damage consultant

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • falkirk (sunny scotland)
  • Posts: 116
    • View Profile
Re: td- lumpy tickover
« Reply #4 on: 05 November 2009, 17:21:48 »
Just had the exact same problem with my tractor take the vacuum pipe of the egr valve and check all the small pipes coming off the brake servo big vacuum pipe for kinks or flattend ones the two pipes disappear into the bulk head on the o/s.
you could also try cleaning out the swirl pot and changing air and fuel filters
Logged

raywilb

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • york
  • Posts: 1874
    • DS DS4
    • View Profile
Re: td- lumpy tickover
« Reply #5 on: 05 November 2009, 20:36:15 »
cheers mate. i will check the pipes tomorrow. i know swirl pot & f/filter are ok. :y :y
Logged

raywilb

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • york
  • Posts: 1874
    • DS DS4
    • View Profile
Re: td- lumpy tickover
« Reply #6 on: 05 November 2009, 21:13:27 »
IanD has explained the prob far better than i :-[
Logged

damage consultant

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • falkirk (sunny scotland)
  • Posts: 116
    • View Profile
Re: td- lumpy tickover
« Reply #7 on: 06 November 2009, 07:47:15 »
Forgot to say try putting a injector treatment in the fuel. the tick over should be 600rpm if that doesn't work you'l have to take it to a fuel injection specialist to see if any injectors need replacing or the fuel pump needs adjusting.
my problem started when the engine stopped whilst traveling it turned out the cotter on the end of the fuel pump shredded luckely chain stayed on thats when all the new faults appeard (34 64 96).had to increase fuel to injectors for 34 and 64 solved its self and 96 was a crushed pipe. I pulled vac pipe off egr and its running better
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.012 seconds with 18 queries.