Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1] 2  All   Go Down

Author Topic: 30 mill lowering, experiences please.  (Read 1579 times)

0 Members and 1 Guest are viewing this topic.

feeutfo

  • Guest
30 mill lowering, experiences please.
« on: 19 October 2010, 04:49:00 »

Certainly with the irmscher body kit on mine the air dam rubs the floor down the far side of speed bumps with 15 mill lower mv6 suspension, and am resigned to never riding over or parking right up to a curb... :(

30 mill is quite a drop, but I love the ride, lack of body roll, and stance this particular suspension kit set up offers  :-*  :y, but will it muller the under side of the car should I fit similar to my new black pride and joy? There are some quite severe speed bumps on my commute... :'(

Anyone else on here got 30 mill drop? And is it a pita?

Ta.
Logged

Kevin Wood

  • Global Moderator
  • *****
  • Offline Offline
  • Gender: Male
  • Alton, Hampshire
  • Posts: 36417
    • Jaguar XE 25t, Westfield
    • View Profile
Re: 30 mill lowering, experiences please.
« Reply #1 on: 19 October 2010, 09:42:47 »

Looks like a choice. Irmscher bits or lowered?

How much rear camber do you end up with after 30mm lowering? There's quite a lot on my MV6 setup, especially if it's fully loaded.

Kevin
Logged
Tech2 services currently available. See TheBoy's price list: http://theboy.omegaowners.com/

F1 9LFG

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • nr Braintree, Essex
  • Posts: 449
    • View Profile
Re: 30 mill lowering, experiences please.
« Reply #2 on: 19 October 2010, 09:50:56 »

hi chris, i dropped my omega when i brought it, had a broken spring so thought it was the perfect time!

i lowered by 40mm and have only rubbed a speed bump once, that was the exhaust catching, and it was a large bump.

i only have stock body parts and being a cdx, not mv6 the ride height was quite high before.

makes a big difference to looks and handling, though oddly the front is lower than the back when the back seats are empty, by a fair amount too.

 :y
Logged

aaronjb

  • Guest
Re: 30 mill lowering, experiences please.
« Reply #3 on: 19 October 2010, 10:00:34 »

Depends if you ever go down Telford Drive in Slough (or anywhere with 'speed cushions' but in by the same people) - they were all but impossible to navigate in the MR2 with it lowered 30mm :-/ it was a case of stop, crawl over hump, drive, stop, crawl over hump, drive.

Really annoyed the 4x4 owners who could go over them at 40mph (did I mention it was a 20 limit outside a school, put there because of the 4x4 owners dropping their kids off? No, that didn't annoy me at all, as you can tell).
Logged

2woody

  • Omega Baron
  • *****
  • Offline Offline
  • Northumberland
  • Posts: 2374
    • View Profile
Re: 30 mill lowering, experiences please.
« Reply #4 on: 19 October 2010, 10:26:23 »

I'd say you'd need to go "off-piste" with the suspension settings if you were to lower beyond the "standard" MV6 spec.

it is highly likely that the roll-centre changes resulting from the lowering will make the handling worse rather than better.

the suspension geometry relies on how the wheels move in relation to the body when in roll. If,for instance, the static position of the lower wishbone is altered at rest (through lowering), the amount that the camber changes with roll will be different that Opel intended, probably incompatible with the roll angle, thereby reducing grip.
Logged

F1 9LFG

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • nr Braintree, Essex
  • Posts: 449
    • View Profile
Re: 30 mill lowering, experiences please.
« Reply #5 on: 19 October 2010, 10:37:21 »

Quote
I'd say you'd need to go "off-piste" with the suspension settings if you were to lower beyond the "standard" MV6 spec.

it is highly likely that the roll-centre changes resulting from the lowering will make the handling worse rather than better.

the suspension geometry relies on how the wheels move in relation to the body when in roll. If,for instance, the static position of the lower wishbone is altered at rest (through lowering), the amount that the camber changes with roll will be different that Opel intended, probably incompatible with the roll angle, thereby reducing grip.

What you say is all very true, however i had full suspension geometry adjusted to suit the 40mm drop and cant say i have noticied any problems in grip, only improvement, even in the wet it is far better on the roundabouts
 :y
Logged

serek

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • huntingdon
  • Posts: 1992
    • 3.2 mv6
    • View Profile
Re: 30 mill lowering, experiences please.
« Reply #6 on: 19 October 2010, 14:21:43 »

got irmscher springs -30mm on mine and dont have any problems with drive over speed bumps :y

feeutfo

  • Guest
Re: 30 mill lowering, experiences please.
« Reply #7 on: 19 October 2010, 15:07:38 »

Quote
Looks like a choice. Irmscher bits or lowered?

How much rear camber do you end up with after 30mm lowering? There's quite a lot on my MV6 setup, especially if it's fully loaded.

Kevin
A phone call to wim is on my list of jobs, the car it's currently fitted to has visibly more camber than mine at the rear!

 Question is why? did the owner not set it correctly? even though the suspension turrets are emblazoned with yellow irmscher stickers announcing a new setting of 1.40 is required? Front looks to be set correctly afaict, so why not adjust the rear? Because it compromises the toe setting excessively? or just didn't bother the with the rear? Or just seized track rods possibly?  :-/

I do wonder if the the toe setting would be miles out if the camber was set with such a low ride hight....? I'll get my head round that piece of geometry one day. The car has a history of tyre wear advisories on the rear... :-/

Logged

Kevin Wood

  • Global Moderator
  • *****
  • Offline Offline
  • Gender: Male
  • Alton, Hampshire
  • Posts: 36417
    • Jaguar XE 25t, Westfield
    • View Profile
Re: 30 mill lowering, experiences please.
« Reply #8 on: 19 October 2010, 16:09:11 »

Quote
Question is why? did the owner not set it correctly? even though the suspension turrets are emblazoned with yellow irmscher stickers announcing a new setting of 1.40 is required? Front looks to be set correctly afaict, so why not adjust the rear? Because it compromises the toe setting excessively? or just didn't bother the with the rear? Or just seized track rods possibly?  :-/

I do wonder if the the toe setting would be miles out if the camber was set with such a low ride hight....? I'll get my head round that piece of geometry one day. The car has a history of tyre wear advisories on the rear... :-/


The camber/toe are a combined "setting" on the track control rods at the rear, so you have a choice of the right camber or the right toe. ;)

The suspension geometry gives extra dynamic camber as it is compressed (designed to keep the tyre contact patch parallel'ish to the road when it rolls during cornering) so by lowering the ride height you are also adding camber which you can't adjust out without bu66ering up the toe.

As 2woody says, you might need to make some changes to make it handle right afterwards.

The reason I mention it is that I know when I get mine aligned they are never happy about the amount of static camber at the rear wheels (well over 2 degrees) but can't do anything about it (and that's with a completely standard MV6 setup).

Having said that, the rear end on mine positively refuses to let go, so something's working OK. :)

Kevin
Logged
Tech2 services currently available. See TheBoy's price list: http://theboy.omegaowners.com/

feeutfo

  • Guest
Re: 30 mill lowering, experiences please.
« Reply #9 on: 19 October 2010, 17:32:39 »

Quote
Quote
Question is why? did the owner not set it correctly? even though the suspension turrets are emblazoned with yellow irmscher stickers announcing a new setting of 1.40 is required? Front looks to be set correctly afaict, so why not adjust the rear? Because it compromises the toe setting excessively? or just didn't bother the with the rear? Or just seized track rods possibly?  :-/

I do wonder if the the toe setting would be miles out if the camber was set with such a low ride hight....? I'll get my head round that piece of geometry one day. The car has a history of tyre wear advisories on the rear... :-/


The camber/toe are a combined "setting" on the track control rods at the rear, so you have a choice of the right camber or the right toe. ;)

The suspension geometry gives extra dynamic camber as it is compressed (designed to keep the tyre contact patch parallel'ish to the road when it rolls during cornering) so by lowering the ride height you are also adding camber which you can't adjust out without bu66ering up the toe.

As 2woody says, you might need to make some changes to make it handle right afterwards.

The reason I mention it is that I know when I get mine aligned they are never happy about the amount of static camber at the rear wheels (well over 2 degrees) but can't do anything about it (and that's with a completely standard MV6 setup).

Having said that, the rear end on mine positively refuses to let go, so something's working OK. :)

Kevin
Aeye, but provided the tyre ware is within "a set or tyres", ie progresive inside edge ware throughout the tyres life with more ware on the inside by the time it's replaced, that will be ok to my thinking, what the limit of that setting is I will discuss with  I guess, if 2degrees gives grip and straight-line stability like yours does i be well happy......
.....what are your rears like across the tread at the end of their life? If excessive camber ends my rear tyres life prematurely then that would be unacceptable obviously  :)    
Logged

Kevin Wood

  • Global Moderator
  • *****
  • Offline Offline
  • Gender: Male
  • Alton, Hampshire
  • Posts: 36417
    • Jaguar XE 25t, Westfield
    • View Profile
Re: 30 mill lowering, experiences please.
« Reply #10 on: 19 October 2010, 17:36:32 »

Quote
Aeye, but provided the tyre ware is within "a set or tyres", ie progresive inside edge ware throughout the tyres life with more ware on the inside by the time it's replaced, that will be ok to my thinking, what the limit of that setting is I will discuss with  I guess, if 2degrees gives grip and straight-line stability like yours does i be well happy......
.....what are your rears like across the tread at the end of their life? If excessive camber ends my rear tyres life prematurely then that would be unacceptable obviously  :)    

Generally, they wear in the centres more than either edge, as if over inflated, despite running them at about 30-32 PSI.

Kevin
Logged
Tech2 services currently available. See TheBoy's price list: http://theboy.omegaowners.com/

feeutfo

  • Guest
Re: 30 mill lowering, experiences please.
« Reply #11 on: 19 October 2010, 17:37:57 »

Quote
hi chris, i dropped my omega when i brought it, had a broken spring so thought it was the perfect time!

i lowered by 40mm and have only rubbed a speed bump once, that was the exhaust catching, and it was a large bump.

i only have stock body parts and being a cdx, not mv6 the ride height was quite high before.

makes a big difference to looks and handling, though oddly the front is lower than the back when the back seats are empty, by a fair amount too.

 :y
Promissing with ground clearance then, there is one big speed hump on my commute that worries me though...
Logged

feeutfo

  • Guest
Re: 30 mill lowering, experiences please.
« Reply #12 on: 19 October 2010, 17:40:21 »

Quote
Depends if you ever go down Telford Drive in Slough (or anywhere with 'speed cushions' but in by the same people) - they were all but impossible to navigate in the MR2 with it lowered 30mm :-/ it was a case of stop, crawl over hump, drive, stop, crawl over hump, drive.

Really annoyed the 4x4 owners who could go over them at 40mph (did I mention it was a 20 limit outside a school, put there because of the 4x4 owners dropping their kids off? No, that didn't annoy me at all, as you can tell).
Tellford drive? I 'll look into that one with a view to avoiding, my problem will be peters field avenue in slough  >:(. Big sb is outside a school though to be fair.
« Last Edit: 19 October 2010, 17:41:08 by chrisgixer »
Logged

feeutfo

  • Guest
Re: 30 mill lowering, experiences please.
« Reply #13 on: 19 October 2010, 18:07:52 »

Quote
Quote
I'd say you'd need to go "off-piste" with the suspension settings if you were to lower beyond the "standard" MV6 spec.

it is highly likely that the roll-centre changes resulting from the lowering will make the handling worse rather than better.

the suspension geometry relies on how the wheels move in relation to the body when in roll. If,for instance, the static position of the lower wishbone is altered at rest (through lowering), the amount that the camber changes with roll will be different that Opel intended, probably incompatible with the roll angle, thereby reducing grip.

What you say is all very true, however i had full suspension geometry adjusted to suit the 40mm drop and cant say i have noticied any problems in grip, only improvement, even in the wet it is far better on the roundabouts
 :y
There will be a proper set up at wheels in motion as usual when ever I play with set up components...

....some thinking on all this set up business...without fully understanding roll centres it has to be said....roll centre, as I vaguely understand it, the  static(?)point the chassis rolls around when cornering, same motion controlled by anti roll bars? So draw a line starting at the roll centre, (i imagine this point to be somewhere along the center line of the crank perhaps? ) outboard towards the wheel and finishing at, I guess, the steering knuckle on the wishbone or just above? If lateral forces are not to affect suspension squatting, then this drawn line needs to have the suspension joints almost exactly along that line taking into account the weight of the car pressing down on it...?

Otherwise, Wang round a corner, sideways motion alone would quat the suspension even without body roll doing the same as well? Or am I way off?

So lowering excessively would move the suspension joints (the wishbone bush joints) off this drawn line.....er.... And basically cocking it all up. But given the various engine weights and ride heights on various models, there must be some leeway?


« Last Edit: 19 October 2010, 18:09:59 by chrisgixer »
Logged

feeutfo

  • Guest
Re: 30 mill lowering, experiences please.
« Reply #14 on: 19 October 2010, 18:11:49 »

Quote
got irmscher springs -30mm on mine and dont have any problems with drive over speed bumps :y
Thanks serek, good news, do you have the front air dam fitted as well?
Logged
Pages: [1] 2  All   Go Up
 

Page created in 0.014 seconds with 16 queries.