Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Omega General Help / Oil Level Warning Switch

« on: 02 May 2012, 23:28:56 »

I have a bad oil leak to my Oil Level Warning Switch and  Iam flumuxed as to how to remove the switch to replace the 'O' ring. Any helpers?
Engine is a 2ltr

2

Omega General Help / Re: Cam Position Sensor

« on: 02 May 2012, 14:35:11 »

Genuine? This part #90458252

I got the part from GSF. It is a Original TOPRAN spare 207 013 756 [replacing 90 12 039] GSF Part No BBH92313
Vehicle is a 2.0ltr
The wiring on the plug has the three wires coloured red   white and black the white wire goes to the inletside of the plug red is the centre wire and black is the one on the exhaust side. Which ones go to which wire on the car loom? as they are differant colours.
Regards Mike

3

Omega General Help / Re: Cam Position Sensor

« on: 02 May 2012, 14:07:43 »

Genuine? This part #90458252

I got the part from GSF. It is a Original TOPRAN spare 207 013 756 [replacing 90 12 039] GSF Part No BBH92313
Vehicle is a 2.0ltr
The wiring on the plug has the three wires coloured red   white and black the red wire goes to the inletside of the plug black is the centre wire and white is the one on the exhaust side. Which ones go to which wire on the car loom? as they are differant colours.
Regards Mike

4

Omega General Help / Cam Position Sensor

« on: 02 May 2012, 13:49:32 »

Old onion I know but have bought a new cam sensor with 4 wires [round cap] What I want to know is which wires conect to which of the 3 wires in the loom?
Regards Mike

5

Omega Electrical and Audio Help / 'Kin Towbar wiring again!

« on: 07 May 2009, 23:26:26 »

Hi Peeps, This may sound old hat as it has cropped up time and again and I suppose a lot of the knowledgable ones amongst you will probibly give this one a big [OH F**K NOT THAT OLD CHESTNUT AGAIN  
Well for anyone who is still reading, this is my delemmer-: I have a 1997 2ltr estate and on inspecting the loom behind the car jack in the wheel well I have come across a Square socket with a wire looped from one hole to another, this part is removable from the plug which is attached to the loom. If this is the plug to use to wire up the tow bar electrics how does one fit the cables into the socket? and of cause the daftest question is which cables go into which holes!!!!!!!
If there is anybody in my area who is knowledgable in this matter who could come and show me what neads to go where I would be most greatfull if he could pop round and sort this problem out for me! 8-)

6

Omega Electrical and Audio Help / Dash light bulb replacement?

« on: 30 January 2008, 23:06:57 »

Any thoughts on the easy (if there is one) changing dash lightbulbs on a '99 migi ? :-?

7

Omega General Help / Re: ECU Managment Light

« on: 27 December 2009, 17:07:30 »

Hum!

8

Omega General Help / Re: ECU Managment Light

« on: 27 December 2009, 16:58:06 »

To tell you the truth, my resistance is getting low, it's fffffking ffffffrezzing out side will continue tomorrow.
If there is any other peoples would like to add there threepence am am all eyes and ears to sugestions.
Oh and a BIG thank you to all that have replied it has been most helpfull. I know thats what were here for, but thanks again.

9

Omega General Help / Re: ECU Managment Light

« on: 27 December 2009, 16:52:04 »

You mean you replaced a wire from the cam sensor to the ecu? Was it a bigger wire[mm/sq] Did you remove the ECU to access the socket?

10

Omega General Help / Re: ECU Managment Light

« on: 27 December 2009, 16:16:40 »

Just earthed it up ----- no response code still reading 0340.
Sensor bought from ebay 200360144426 Trusting that this is a reprutable source.

11

Omega General Help / Re: ECU Managment Light

« on: 27 December 2009, 15:55:11 »

You may just be correct in your assumpsion as I did notice the other wire but did ignore it. I will now go and connect said wire to ground+

12

Omega General Help / Re: ECU Managment Light

« on: 27 December 2009, 15:43:56 »

It has been replaced with the GM modified one. This had been fitted prior to my owning the car. Have fitted the new cable that came with the replacement sensor and soildered the wires on to the same positions as before as the colour codes on the wires do not match for what ever reason!

13

Omega General Help / Re: ECU Managment Light

« on: 27 December 2009, 15:35:32 »

Code No :- 0340
Help with code please!

14

Omega General Help / Re: ECU Managment Light

« on: 27 December 2009, 15:22:26 »

Will give the clip test a try and get back soon.

15

Omega General Help / ECU Managment Light

« on: 27 December 2009, 15:01:58 »

Just changed cam shaft sensor on my 2.0ltr Mig and the ECU light is still on. It is still limiting revs to 3600ish ie safety mode.
Any ideas welcome.