Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Omega General Help / Re: wipers

« on: 18 June 2010, 23:47:41 »

That will be the nut loose on the wiper motor, scuttle off,loosen nut further, lift the kinked arm off a little, reposition wipers with kinked arm between arrows on casting, tighten nut, re fit scuttle.

thank you just as you said nut was loose.

2

Omega General Help / Re: wipers

« on: 18 June 2010, 19:43:43 »

thanks will try that. wipers are working fine but stop in wrong position.

3

Omega General Help / wipers

« on: 18 June 2010, 14:39:15 »

hi all just drove through some heavy showers now when i switch off wipers they stay in the vetical position blocking my vision. any ideas please

4

Omega General Help / Re: omega 2.2 limp mode

« on: 28 February 2010, 15:38:09 »

thanks again will get one tomorrow and let you know what happens

5

Omega General Help / Re: omega 2.2 limp mode

« on: 28 February 2010, 14:59:41 »

hi got a refund and free replacement for my trouble.fitted it outside shop and was worse than before.called rac .here are the codes p0120-p1120 throttle. po340 cam sensor again. p1405-egr. p0170=bank 1 o2 sensor. would only rev with cam sensor plug disconnected. got home eventually and very slowly like that followed by rac. surely 3 cam sensors cant be no good. taking to garage in morning but any solutions would help. thanks andy

6

Omega General Help / Re: omega 2.2 limp mode

« on: 27 February 2010, 18:28:10 »

just to double check was this bought from eBay as 'genuine' or did you get it from a Vx dealer?

hi it was sold to me as genuine by local motor factors.
£68 sound right.

7

Omega General Help / Re: omega 2.2 limp mode

« on: 27 February 2010, 18:26:16 »

thanks understand now

8

Omega General Help / Re: omega 2.2 limp mode

« on: 27 February 2010, 18:01:04 »

thanks for info. if that is the case why has eml gone out and spanner light come on.

9

Omega General Help / Re: omega 2.2 limp mode

« on: 27 February 2010, 17:50:49 »

hi yes i did

10

Omega General Help / omega 2.2 limp mode

« on: 27 February 2010, 17:44:29 »

hi all can anyone help.
eml light came on last week had codes read and came up cam sensor. just changed it and got the light to go out by starting 15 times cleanly. went for a run but still will not rev over 4000 rpm.now spanner light has come on. will not go out by restarting. all usual things checked breathers-egr . no oil in plug wells.

11

Omega General Help / no revs

« on: 28 August 2009, 22:58:06 »

hi all my 2001 2.2 cdx auto petrol starts fine and idles but will not rev at all. any ideas please

12

Omega General Help / Re: 2.2 starting problem and warning light

« on: 01 December 2008, 21:01:57 »

http://users.volja.net/grebenm/plx/x20xev/x20xev.html.
hi found it.
regards andy

13

Omega General Help / Re: 2.2 starting problem and warning light

« on: 01 December 2008, 20:54:21 »

hi took me less than i hour and a can of degreaser.
there is a guide on here with pictures. i stumbled across it.
i am sure one of the more experienced members will post you a link to it.
andy

14

Omega General Help / Re: 2.2 starting problem and warning light

« on: 01 December 2008, 20:31:55 »

hi i had the same problem on my 2.2.
it was a blocked breather jet in throttle body.
hope this helps. andy

15

Omega General Help / Re: oil leak 2.2 petrol

« on: 28 November 2008, 13:51:50 »

thanks for replies. had a look in daylight.
leaking from rear of cam cover. thankfully.
andy