Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: 1 [2]  All   Go Down

Author Topic: washer bottle/pump part No. ?  (Read 3180 times)

0 Members and 1 Guest are viewing this topic.

powerslinky

  • Guest
Re: washer bottle/pump part No. ?
« Reply #15 on: 29 June 2014, 19:26:52 »
Quote from: Taxi Al on 29 June 2014, 19:19:46
Could try three turns of tape around the pump body between the seal and the first clip on the bottle...

hi Al,    yer was thinking along those lines .  Pump pulls out of the grommet very easily . Seem to recall that usually the grommet would come away from the bottle with the pump when pulled out. End of the day  a new grommet/seal should not be much  :P :P     
Logged

Toledodude1973

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • IPSWICH U.K.
  • Posts: 1300
  • 2002 2.6 elite,1973 ,Gas van,1974 victor fe
    • 2.6 OMEGA ELITE 2002
    • View Profile
Re: washer bottle/pump part No. ?
« Reply #16 on: 29 June 2014, 19:39:31 »
How good is Robg with part no.s and pictures,invaluable to this site :y
Logged
2002 omega slowly morphing into 2003 omega with increasing doner parts fitted

Steve B

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Leicestershire
  • Posts: 3639
    • '52' MV6 3.2 Saloon
    • View Profile
Re: washer bottle/pump part No. ?
« Reply #17 on: 29 June 2014, 20:40:51 »
Quote from: Toledodude1973 on 29 June 2014, 19:39:31
How good is Robg with part no.s and pictures,invaluable to this site :y
He said give me 5 mins.But it took him nine mins. :y You need to speed up rob  :y
Logged

powerslinky

  • Guest
Re: washer bottle/pump part No. ?
« Reply #18 on: 29 June 2014, 20:43:15 »
Quote from: bigtimecube on 29 June 2014, 20:40:51
Quote from: Toledodude1973 on 29 June 2014, 19:39:31
How good is Robg with part no.s and pictures,invaluable to this site :y
He said give me 5 mins.But it took him nine mins. :y You need to speed up rob  :y

It is sunday Bigtime ;D ;D   but info was brill   . .  as usual  :y :y
Logged

powerslinky

  • Guest
Re: washer bottle/pump part No. ?
« Reply #19 on: 29 June 2014, 20:44:14 »
Quote from: Toledodude1973 on 29 June 2014, 19:39:31
How good is Robg with part no.s and pictures,invaluable to this site :y

Without doubt    :y :y
Logged

Toledodude1973

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • IPSWICH U.K.
  • Posts: 1300
  • 2002 2.6 elite,1973 ,Gas van,1974 victor fe
    • 2.6 OMEGA ELITE 2002
    • View Profile
Re: washer bottle/pump part No. ?
« Reply #20 on: 29 June 2014, 20:54:37 »
I might take it back after the 4 min delay ;D
Logged
2002 omega slowly morphing into 2003 omega with increasing doner parts fitted

amba

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Medway towns
  • Posts: 4827
    • German V6
    • View Profile
Re: washer bottle/pump part No. ?
« Reply #21 on: 29 June 2014, 22:00:05 »
Al.

I had a similar issue with my Headlight Washer Pump as the reservoir would empty even without using the washer .Traced mine to the pump not seating into the rubber grommet properly.

Cure I found was to put a few wraps of PTFE tape around the end of the pump then push the rubber grommet onto the pump end.Then fitted the entire assembled unit into the hole in the reservoir and it solved the leak and hasnt lost a drop since. :y 
Logged

powerslinky

  • Guest
Re: washer bottle/pump part No. ?
« Reply #22 on: 30 June 2014, 07:07:35 »
Quote from: amba on 29 June 2014, 22:00:05
Al.

I had a similar issue with my Headlight Washer Pump as the reservoir would empty even without using the washer .Traced mine to the pump not seating into the rubber grommet properly.

Cure I found was to put a few wraps of PTFE tape around the end of the pump then push the rubber grommet onto the pump end.Then fitted the entire assembled unit into the hole in the reservoir and it solved the leak and hasnt lost a drop since. :y

Hi Andrew,  My pump seems a slack fit into the grommet  . . .  Will try the PTFE tape then . . .   :y
 
Logged

Jimbob

  • Global Moderator
  • *****
  • Offline Offline
  • Gender: Male
  • Chester / Flintshire
  • Posts: 24525
  • I like traffic lights, but only when they're green
    • E250 Est / Golf GTI
    • View Profile
Re: washer bottle/pump part No. ?
« Reply #23 on: 30 June 2014, 07:53:22 »
I had to buy one of those in the past. After removal could never get it to seal again. New one. And perfection returned
Logged
Pages: 1 [2]  All   Go Up
« previous next »
 

Page created in 0.012 seconds with 17 queries.